Dyno Graphs
#427
Back in the BOOST Game
iTrader: (15)
New Dyno Run after going NS
http://i535.photobucket.com/albums/e...-StCharles.jpg
I haven't gotten my tune 100% sorted out as of yet, but this serves as a good re-baseline to build from. 315RWHP and almost 280RWTQ. Mods are as follows:
1994 BB PEP RX-7 w/36xxx miles original (stock ports obviously)
NS Twins @ 14ish PSI, Ported, Polished and Gasket Matched to the Downpipe
Turbo Manifold Ported Polished & Gasket Matched
Wastegate Ported
M2 CAI
M2 Medium IC
Polished Greddy Elbow
Polished Hardpipes all around
Koyo NFlo Radiator
PFS aluminum AST
R1 Dual Oil Coolers
Pineapple Racing Idler Puller (air pump & Emissions Delete)
1200cc secondaries, 550cc primaries
PFC With a solid Steve Kan dyno tune (pre NS conversion)
HKS TwinPower
NGK 9s all around
Bonez Hi-flow Cat
Racing Beat Dual tip Cat back
3" downpipe
PFS Engine Grounds
TurboJeff Battery Tray
Fast Reaction IAT sensor
Eibach & Tokicos all around
Polished and powdercoated R1 Strut Bar
Banzai Diff Brace
MazdaSpeed Differential Carrier bushings
I haven't gotten my tune 100% sorted out as of yet, but this serves as a good re-baseline to build from. 315RWHP and almost 280RWTQ. Mods are as follows:
1994 BB PEP RX-7 w/36xxx miles original (stock ports obviously)
NS Twins @ 14ish PSI, Ported, Polished and Gasket Matched to the Downpipe
Turbo Manifold Ported Polished & Gasket Matched
Wastegate Ported
M2 CAI
M2 Medium IC
Polished Greddy Elbow
Polished Hardpipes all around
Koyo NFlo Radiator
PFS aluminum AST
R1 Dual Oil Coolers
Pineapple Racing Idler Puller (air pump & Emissions Delete)
1200cc secondaries, 550cc primaries
PFC With a solid Steve Kan dyno tune (pre NS conversion)
HKS TwinPower
NGK 9s all around
Bonez Hi-flow Cat
Racing Beat Dual tip Cat back
3" downpipe
PFS Engine Grounds
TurboJeff Battery Tray
Fast Reaction IAT sensor
Eibach & Tokicos all around
Polished and powdercoated R1 Strut Bar
Banzai Diff Brace
MazdaSpeed Differential Carrier bushings
#428
Senior Member
iTrader: (1)
http://www.dangerzonejobs.com/artman...sh/index.shtml
http://img190.imageshack.us/i/dynoinfo1.jpg/
Just wanted to say got back from Lowes performance in Sarasota Florida. Mike did a great good on the rebuild of my engine. And thank you to A-spec for getting my turbo back and fixed from Garrett in a timely manner. Sorry Ryan for being so pushy.
Here is what happened: Have a 500R, with the billet housing, PFC, 550/1600, walbro fuel pump, meth injection running boost juice, Apexi twin power greeddy boost controller, AEM wide band. 4inch , straight trough black Apex seals, street ported by Mike and build. and some other stuff.
For some reason the waste gate wasn't holding boost, there was a 11lb. spring in it but still shooting up way high. Mike was saying how I need a higher wastegate ie: instead for 44mm. a 50.
Brought it over to the dyno and the 1st run made 405 at 15psi. and about 7,000rpm. The 2nd run did 456 and went past 15, it was around 17psi. at 7400rpm. Mikes son had to let off cause fuel was running out. I guess the fuel pump couldn't keep up. Regardless I am totally stoked with the power this thing made toady, absolutely phenomenal.
Mike then wanted to check the meth injection to make sure it was working. We undid the nozzle and found out the it was only shooting out very little boost juice maybe 1oz. each time. Pretty sure it should be coming out a lot more then that right?
I recommend anyone to go to his shop and get work done. Car pulls like no tomorrow and its pretty scary to drive.
I will post the sheet soon.
http://img190.imageshack.us/i/dynoinfo1.jpg/
Just wanted to say got back from Lowes performance in Sarasota Florida. Mike did a great good on the rebuild of my engine. And thank you to A-spec for getting my turbo back and fixed from Garrett in a timely manner. Sorry Ryan for being so pushy.
Here is what happened: Have a 500R, with the billet housing, PFC, 550/1600, walbro fuel pump, meth injection running boost juice, Apexi twin power greeddy boost controller, AEM wide band. 4inch , straight trough black Apex seals, street ported by Mike and build. and some other stuff.
For some reason the waste gate wasn't holding boost, there was a 11lb. spring in it but still shooting up way high. Mike was saying how I need a higher wastegate ie: instead for 44mm. a 50.
Brought it over to the dyno and the 1st run made 405 at 15psi. and about 7,000rpm. The 2nd run did 456 and went past 15, it was around 17psi. at 7400rpm. Mikes son had to let off cause fuel was running out. I guess the fuel pump couldn't keep up. Regardless I am totally stoked with the power this thing made toady, absolutely phenomenal.
Mike then wanted to check the meth injection to make sure it was working. We undid the nozzle and found out the it was only shooting out very little boost juice maybe 1oz. each time. Pretty sure it should be coming out a lot more then that right?
I recommend anyone to go to his shop and get work done. Car pulls like no tomorrow and its pretty scary to drive.
I will post the sheet soon.
#430
Senior Member
Join Date: Jul 2001
Location: Sarasota FL/Ft Lauderdale
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
http://www.dangerzonejobs.com/artman...sh/index.shtml
http://img190.imageshack.us/i/dynoinfo1.jpg/
Just wanted to say got back from Lowes performance in Sarasota Florida. Mike did a great good on the rebuild of my engine. And thank you to A-spec for getting my turbo back and fixed from Garrett in a timely manner. Sorry Ryan for being so pushy.
Here is what happened: Have a 500R, with the billet housing, PFC, 550/1600, walbro fuel pump, meth injection running boost juice, Apexi twin power greeddy boost controller, AEM wide band. 4inch , straight trough black Apex seals, street ported by Mike and build. and some other stuff.
For some reason the waste gate wasn't holding boost, there was a 11lb. spring in it but still shooting up way high. Mike was saying how I need a higher wastegate ie: instead for 44mm. a 50.
Brought it over to the dyno and the 1st run made 405 at 15psi. and about 7,000rpm. The 2nd run did 456 and went past 15, it was around 17psi. at 7400rpm. Mikes son had to let off cause fuel was running out. I guess the fuel pump couldn't keep up. Regardless I am totally stoked with the power this thing made toady, absolutely phenomenal.
Mike then wanted to check the meth injection to make sure it was working. We undid the nozzle and found out the it was only shooting out very little boost juice maybe 1oz. each time. Pretty sure it should be coming out a lot more then that right?
I recommend anyone to go to his shop and get work done. Car pulls like no tomorrow and its pretty scary to drive.
I will post the sheet soon.
http://img190.imageshack.us/i/dynoinfo1.jpg/
Just wanted to say got back from Lowes performance in Sarasota Florida. Mike did a great good on the rebuild of my engine. And thank you to A-spec for getting my turbo back and fixed from Garrett in a timely manner. Sorry Ryan for being so pushy.
Here is what happened: Have a 500R, with the billet housing, PFC, 550/1600, walbro fuel pump, meth injection running boost juice, Apexi twin power greeddy boost controller, AEM wide band. 4inch , straight trough black Apex seals, street ported by Mike and build. and some other stuff.
For some reason the waste gate wasn't holding boost, there was a 11lb. spring in it but still shooting up way high. Mike was saying how I need a higher wastegate ie: instead for 44mm. a 50.
Brought it over to the dyno and the 1st run made 405 at 15psi. and about 7,000rpm. The 2nd run did 456 and went past 15, it was around 17psi. at 7400rpm. Mikes son had to let off cause fuel was running out. I guess the fuel pump couldn't keep up. Regardless I am totally stoked with the power this thing made toady, absolutely phenomenal.
Mike then wanted to check the meth injection to make sure it was working. We undid the nozzle and found out the it was only shooting out very little boost juice maybe 1oz. each time. Pretty sure it should be coming out a lot more then that right?
I recommend anyone to go to his shop and get work done. Car pulls like no tomorrow and its pretty scary to drive.
I will post the sheet soon.
I'd just like to second the recommendation of Mike and his shop. He has been a friend for years and has done all the work on my 93 RX 7. Mikes been working on rotarys for over 25 years now. And he was the 2003 ASA-ASE National Mechanical Technician of the year.
He knows his stuff and the cars he builds and tunes run right.
Mike and his crew have been working on my car slowly over the last several months while I'm working out of town and it should be going to the dyno soon. I'll post the sheet once it does.
(It's the yellow one radiant. You may have seen it in his shop.)
#432
that random guy
iTrader: (3)
Join Date: Jun 2007
Location: Queens, NY
Posts: 331
Likes: 0
Received 0 Likes
on
0 Posts
383 whp at 12.5 psi
93 touring lg streeport motor
new gt3582r a-spec turbo mani
unknown fmic (came with car)
greddy 3.5" catback
hks twin spark
power fc tuned by enzo
and some other goodies
new added parts waiting to go back to the dyno
meth injection and now on 14.5-15 psi (only pulling to 7k as a I need a bigger wg)
new clutch (still had stocker on last dyno runs)
video in sig
93 touring lg streeport motor
new gt3582r a-spec turbo mani
unknown fmic (came with car)
greddy 3.5" catback
hks twin spark
power fc tuned by enzo
and some other goodies
new added parts waiting to go back to the dyno
meth injection and now on 14.5-15 psi (only pulling to 7k as a I need a bigger wg)
new clutch (still had stocker on last dyno runs)
video in sig
#434
Who say's i need a Van
iTrader: (18)
Join Date: Feb 2009
Location: Whatsittoya
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
93 automatic
93 Auto
stock port
2nd engine with 39,000mi
92,500mi on chassis
POWER:
DP
Midpipe
Cat-back
PFS SMIC
Power FC & Commander
Banzai Auto FC harness
Pettit intake
Water methanol injection (for reliability not for increased boost and timing)
Walbro 255hp fuel pump (with additional ground wire)
Tuned to 13.5 psi
Dynoed @ 309rwhp
RELIABILITY:
AST
Pettit 185 fan switch
3 speed fan mod
upgraded radiator
stock port
2nd engine with 39,000mi
92,500mi on chassis
POWER:
DP
Midpipe
Cat-back
PFS SMIC
Power FC & Commander
Banzai Auto FC harness
Pettit intake
Water methanol injection (for reliability not for increased boost and timing)
Walbro 255hp fuel pump (with additional ground wire)
Tuned to 13.5 psi
Dynoed @ 309rwhp
RELIABILITY:
AST
Pettit 185 fan switch
3 speed fan mod
upgraded radiator
#437
LSx 7.0L
iTrader: (20)
Just dyno'd again at KDR yesterday. On 23 psi we made 516RWHP and 414RWTQ. My PowerFC drivers are not controlling my boost solenoid correctly, so I'm going back in a couple weeks with a Blitz iD Spec R so that we can make closer to 570. Anyway, here is the video and the plot...Enjoy!
http://www.youtube.com/watch?v=pcHie...layer_embedded
http://i291.photobucket.com/albums/l...1/IMG_0793.jpg
http://www.youtube.com/watch?v=pcHie...layer_embedded
http://i291.photobucket.com/albums/l...1/IMG_0793.jpg
#441
LSx 7.0L
iTrader: (20)
I've got the RP fuel pump from rx7.com, kgparts fuel rail, 850cc primaries, 1600cc secondaries, and an Aeromotive AFPR.
Right now the restriction I'm running into is the actual line itself. I said I'd be happy with over 500 though, so I'm trying to stick by that statement. :P
Right now the restriction I'm running into is the actual line itself. I said I'd be happy with over 500 though, so I'm trying to stick by that statement. :P
#442
T O R Q U E!
iTrader: (24)
Just dyno'd again at KDR yesterday. On 23 psi we made 516RWHP and 414RWTQ. My PowerFC drivers are not controlling my boost solenoid correctly, so I'm going back in a couple weeks with a Blitz iD Spec R so that we can make closer to 570. Anyway, here is the video and the plot...Enjoy!
#443
LSx 7.0L
iTrader: (20)
Very impressive power and torque, that must be a total monster on the street. Can you post your dyno graph, better yet, do you have the dynojet run files you can post as well? What RPM do you make desired boost? You should be running 10's in this thing at well over 120 mph!
#445
LSx 7.0L
iTrader: (20)
Sorry, don't have a scanner. Took a picture of the dyno sheet, but didn't come out great...
http://i291.photobucket.com/albums/l...o_sheet002.jpg
http://i291.photobucket.com/albums/l...dyno_sheet.jpg
http://i291.photobucket.com/albums/l...o_sheet002.jpg
http://i291.photobucket.com/albums/l...dyno_sheet.jpg
#448
Junior Member
Join Date: Jun 2009
Location: portland OR.
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
pineapple motor & street port ,gt35r@13 psi,extreme fuel rail with 850 primary & 1600 secondary,walboro fuel pump,power fc,koyo radiator,custom intercooler & pipe,meth injection, max power =377.8@6450rpm, max torque=327.4@5550
#450
Here is my most recent dyno sheet 621whp/482tq @ 17psi
http://www.banzai-racing.com/dyno_ch...o_09-23-10.jpg
and a vid
http://www.youtube.com/watch?v=D8UtdvLO6ZY
http://www.banzai-racing.com/dyno_ch...o_09-23-10.jpg
and a vid
http://www.youtube.com/watch?v=D8UtdvLO6ZY