RX7Club.com - Mazda RX7 Forum - View Profile: Banzai-Racing

Go Back  RX7Club.com - Mazda RX7 Forum > Members
Reload this Page > Banzai-Racing's Profile
RX7Club Vendor

Banzai-Racing Banzai-Racing is online now

Rotary Specialists

Visitor Messages

Showing Visitor Messages 1 to 10 of 22
  1. SiNfidelity
    08-10-16 09:30 AM - permalink
    Hi Banzai
    I noticed u seem to know Sh!tloads about rotors, so I'm hoping u can answer this for me, please.
    Are a 20b omp wiring (6pin plug omp side) pin positions The same as a s5 omp plug?
    I have a wiring diagram for wiring up a s5 omp to aftermarket ECU idle controls 1-4, but I don't have one for my 20b. I need to know if I can just follow the pin positions in the plug of 20b and wire them as per the s5 omp, regardless of the colour differences.
    Thanks u in advance.
  2. moosahb
    12-06-14 04:41 PM - permalink
    Hi

    I am new to rotary & just got back my RX7 FD3S. It has been modified after the seals blew. The mods are 550cc primary injectors, custom v-mount intercooler, customer manifold and a s300sx 366 turbo with .91A/R t4 divided.

    I have read some of your posts and am amazed with your knowledge and was hoping for some assistance. Here in south Africa I cant seem to find a tuner that really knows how to tune. My current tune is so bad that if I try and cruise the car keeps 'stuttering' but under acceleration I have no problems. The car is also tuned to run 10 afr.

    I have a microtech 11 fitted in the car and have met a piston tuner who is highly regarded in the tuning in South Africa. He is willing to tune my car. Some tuners say that the rotary should not be given any timing, must be as rich as hell, etc.

    I would like some assistance and advise on how to tune the rotary, what to look out for and what to not do. Any assistance will be greatly appreciated
  3. stickmantijuana
    09-29-13 10:43 AM - permalink
    hey guys, I have LT16 with 20b and 900cc primaries. do you have any base map you can share? I also have a TPS issue... wiring is correct, but TPS reads 99% when throttle is closed, and I can't adjust it down to 0%. even when I disconnect TPS, microtech reads 99% TPS position... your help is really appreciated. thank you.
  4. gmpaul
    07-22-13 01:56 PM - permalink
    can you please help me find a rear window louver for a 1986 mazda rx7? I have been searching this site for month and craigslist....
  5. rotarr
    03-23-13 08:50 PM - permalink
    ok thanks for your input it was very helpful and i think i will start on my rebuild very soon,anyways name is jj and i am from canada thanks again
  6. rotarr
    03-23-13 07:24 PM - permalink
    Hi there i did an compression test turned out the front rotar has no compression and the rear has 90 psi so i am thinking this is my problem is it thanks
  7. rotarr
    03-18-13 11:02 PM - permalink
    there fellow i am an newbe and i need some help i am looking at any option my user name is rottar,to start with my car is an 91 S5 N/A an i did an JDM S5 T2 swap the problem i am having is after the swap i just done some weeks ago i am trying to start it and it cranks over and over and it will not start and it just floods rite out i have spark and i have try with the spear cas i got and i could hear my injectors and also saw my plugs sparking so i have no idear whats going on also i am useing an S5 N/A harness any help will be apreciated thanks just need my car to start thanks
  8. Derickrx785
    03-27-11 05:09 PM - permalink
    i am buying a 13b turbo rotary with transmission to place in my 1985 gsl rx7 12a, i would like to know what other parts and such i will need to make this work, any and all help would be greatly appreciated. please send all info to [email protected]
  9. TrboSpdAnt
    08-07-10 01:43 AM - permalink
    Hey, man, just wanted to thank you a shit-ton for all of your help with my Code 58 issue... If possible, can you note/ PM me a cost for both a PFC and a decent boost-controller, shipped, to 32606?

    Once again, thanks a TON, brother; I owe you one!
  10. careet
    02-14-10 09:25 PM - permalink
    Hey guys, it's Tom from Friday (black '90 na FC)

    Thanks again for all of the help, she's running like a champ.

About Me

  • About Banzai-Racing
    Car
    93 FD3s
    Location
    Indiana
    Occupation
    Rotary Engine & Turbo Specialist
    Gender
    Male
  • Signature


    Like our Facebook Page

Statistics

Total Posts
Albums
Visitor Messages
Total Thanks
General Information
  • Last Activity: 12-13-17 06:06 AM
  • Join Date: 01-18-08

Friends

Showing Friends 1 to 10 of 27

Social Profiles

Instant Messaging
Send an Instant Message to Banzai-Racing Using...
Home Page
http://www.banzai-racing.com/
This Page
https://www.rx7club.com/members/banzai-racing-111536/

All times are GMT -5. The time now is 06:09 AM.


All content Copyright 2007 by Internet Brands, Inc. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.