DamnitzRoger

iTrader: (3)

nw off of 249 and beltway 8. any help is appreciated right now but after the insurance company takes a look at it ill see if they are willing to pay for mechanical work. if not then i'm on my own

hatemy7

hey dont worry, ur ok regardless, bc RX7 nut knows his ****....you should check out the video of his 550hp rx7, well the start up....

cewrx7r1

iTrader: (2)

Sounds like it is firing on only one rotor or only on the trailing plugs.

If you had a PFC ecu, it would be easy to verify.

If running only on trailing plugs and you advance the IGT, the engine would smooth out. That would mean your leading coil was bad (that is if the plugs and cables are good).

Then you can play with the leading injector lag times to lean or richen the #1 or #2 rotors to see if it is only running on one rotor or that rotor has an injector leak.

DamnitzRoger

iTrader: (3)

hm.. im not sure what the IGT is, this car is completely stock with no modifications. i'm gonna have to read more into this

DamnitzRoger

iTrader: (3)

well the car was sent to a shop for a estimate on body damages and later mechanical damages if any.

scca racer

The new shop manager down at Lonestar Motorsport, the shop at MSR Houston was the rotary guy up in Colorado for a long time. he has experience in building racing motors, and has gotten a lot more power out of my GSL-SE. Look him up at www.mrshouston.com his name is Louis Rivera.

Tell him Scott sent you.

romelgranda

Hello guys

hi I wanted to know if there is any performance or regular mechanic in the Houston area that work on rx7 I am bringing my 86 rx from florida down here and I need a mechanic, down in Florida I have taken my car to the same mechanic for years and its hard to find a good mechanic that wont screw you over any help would be appreciated


thank you guys

romelgranda

Hello guys

hi I wanted to know if there is any performance or regular mechanic in the Houston area that work on rx7 I am bringing my 86 rx from florida down here and I need a mechanic, down in Florida I have taken my car to the same mechanic for years and its hard to find a good mechanic that wont screw you over any help would be appreciated


thank you guys

BushyTea

iTrader: (4)

I am not sure if there is or not but you might check out houseperformancedriving.com and ask on there. I am a member there but alot of guys there know the guys to go to or not for your cars.

Mike

cewrx7r1

iTrader: (2)

There aren't any RX7 performance shops in Houston.
MazMax is an independant RX7 shop that repairs but does not mod rotorys.

A few of us mod cars and engines. Kyle and I work on FDs but not earlier 7s except engine rebuilds.

romelgranda

Thank you i will look there

romelgranda

Ok i will look them up thank you
how about Austin

dmundy

Look up Lucas Automotive and Restoration for basic stuff, Engine Logics does some neat work. You need to not be an overly sensitive human at either shop! You might see if Tony Rivera is doing side work, I think he is still doing engine work.
Good Luck,
Dave

romelgranda

ok thanks i will look in to that

chemicool

iTrader: (1)

The guy down a Rotary Performance Plus I heard was good. His name is Gabriel. Be sure to bring one of these though!


Seriously, don't go to him.

manuelxj

iTrader: (2)

just need some pointers as in where to go to get my 7 tuned ..im kinda hopeing theres a place i can go here in houston
It's a 86 base
s5 TII swap
TII tranny, mazdatrix driveshaft
megasquirt standalone, new wiring harness
tech edge wideband
profec B boost controller, not hooked up
trust exhaust
intake
fd fuel pump
FD alternator

i need to get it tuned so i can get to driving the car..so any help i would be very thankfull for

JStewart

Gotham racing
BDC

are both great places

BDC

Manuel,

I converted over a couple of my timing sets from my Haltech stuff into use for the Megasquirt. They're in the form of 12x12 tables that you guys use. They're posted up on the Megasquirt section of this forum but you can also access them from here:

http://bdc.cyberosity.com/v/Technica...ch/MegaSquirt/

That ought to help with how the car runs. For the time being, you can mess with fuel tuning stuff but be careful with it especially if you aren't very familiar with the software and the ECU. Don't load the car out and run a bunch of boost until it's tuned.

B

manuelxj

iTrader: (2)

alrighty thanks for that i guess i need just get my lazy butt out of the house to go buy a laptop so i can get this done...
i havent been driving the car cuz i didnt want to mess it up due to it not runing right

Rx7_Nut13B

iTrader: (1)

Well i am not the best at the MS but i am local and know everything with rotaries.

BDC

Must be nice to know everything with rotaries.

B

s1mpsons

iTrader: (5)

Sorry to hijack the thread, but can someone please PM me the names of some reputable rx7 shops in houston, tx?

Thanks!
Jake

DrKillJoY

There really aren't any "reputable" shops in Houston (for rotaries).

You might consider coming out to a meeting and getting to know some of our local experts.

I merged your post in with a thread about the topic.

Rx7_Nut13B

iTrader: (1)

Well i guess I will refresh my info on this thread..


Rx7_Nut13B............. Email Ccoutts@36db.com

Rebuild for 12A's and 13B's !!!!Cheap prices!!!! But Quality Work...... ASK AROUND

Porting work for motors, I love to Bridge-Port motors !!!!!!!! But anything you want


1st Gens - I can do almost anything except suspension work....

2nd Gens - Expert at Turbo Swaps, Everything else... Lots of Spare Parts

3rd Gens - Just about anything, Single Turbo conversions, ect.

philiptompkins

iTrader: (4)

Apparently rotaries don't know English