F/S MHI t67 T4... fresh rebuild!! (td07 25g)
08-07-08, 10:07 PM
#1
Junior Member
Thread Starter
Join Date: Aug 2008
Location: zebulon NC
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
F/S MHI t67 T4... fresh rebuild!! (td07 25g)
sorry this is not in the correct sub forum, but i cannot post in the classifieds yet. I NEED to get a gt35r BAD but i am strapped for cash and must sell my T67 for the funds..
again, sorry for posting this in the wrong place, but i thought if i should post it anywhere it should be an Rx7 forum because rotarys spool the hell out of turbos unlike my sr20 haha
turbo is a MHI ( same as greddy and trust ) t67 td07 25g 8cm with a fresh pro rebuild.. i put it on my sr20 and it is WAY to laggy for what i want..NO in/out shaft play at all.. i put about 3 miles on the rebuild and there where no leaks or smoke, it performed perfectly
4 inch inlet, 3 inch outlet ( Vband FTW)
price is 650 shipped...
again, sorry for posting this in the wrong place, but i thought if i should post it anywhere it should be an Rx7 forum because rotarys spool the hell out of turbos unlike my sr20 haha
turbo is a MHI ( same as greddy and trust ) t67 td07 25g 8cm with a fresh pro rebuild.. i put it on my sr20 and it is WAY to laggy for what i want..NO in/out shaft play at all.. i put about 3 miles on the rebuild and there where no leaks or smoke, it performed perfectly
4 inch inlet, 3 inch outlet ( Vband FTW)
price is 650 shipped...
08-08-08, 11:33 AM
#3
Where is my Life ?
iTrader: (2)
Join Date: Nov 2003
Location: ottawa canada
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts
some people might be interested.
just that.
your newer to the forum. So its a little harder and the 8cm hotside isnt the best for the 13b ( real small ).
just that.
your newer to the forum. So its a little harder and the 8cm hotside isnt the best for the 13b ( real small ).
08-08-08, 10:05 PM
#6
Where is my Life ?
iTrader: (2)
Join Date: Nov 2003
Location: ottawa canada
Posts: 2,175
Likes: 0
Received 0 Likes
on
0 Posts
Ya on a piston motor youll need a very aggressive cam Im guessing.
in a rotary thats a VERY SMALL hotside, and would probably choke the motor, you would need around a 16cm ( double the side ) hotside to run nicely in a rotary.
Added cost of $ 300-$ 500 to get the right hotside might turn some people off.
rough aproximation , but the 8cm would be like a .50 hotside on a T4 or along those lines. Most 13bs will run atleast a .84 to 1.1x .
But I bet the honda guys with some funny gas will love that, put it on ebay and it will sell very quickly !
08-09-08, 12:00 AM
#7
Junior Member
Thread Starter
Join Date: Aug 2008
Location: zebulon NC
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
oopps.. maybe im mistaken then.. might be a 12cm... can you tell from the pics?
its defffffintaly not a .50 alot higher then that
a gt35r .63 hit set boost on my car @ 5000ish.... this thing doesnt see set boost till about 7k in 1st gear
its defffffintaly not a .50 alot higher then that
a gt35r .63 hit set boost on my car @ 5000ish.... this thing doesnt see set boost till about 7k in 1st gear
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM
eplusz
General Rotary Tech Support
15
10-07-15 04:04 PM
Blk 93
3rd Generation Specific (1993-2002)
7
09-28-15 01:45 PM
