>< what the..
#1
Junior Member
Thread Starter
Join Date: Aug 2007
Location: Yelm, WA
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
>< what the..
Alright, well I started my car today and something is wrong, none of my warning light s are coming on. What do I have to do to fix this...
#2
? I don't get it. SO your car STARTS but the idiot lights DO NOT come on? Is there any way for you to be more specific about the problem and can you make the thread title a little less shitty?
#5
Junior Member
Thread Starter
Join Date: Aug 2007
Location: Yelm, WA
Posts: 34
Likes: 0
Received 0 Likes
on
0 Posts
That is not good, rx-7's are suppose to show their lights so you know they work and etc. The title dont worry about it gee, just need to know how to fix them. The dash lights at the top center console are not lighting up when I turn the car on or even when I just turn the key, how would I fix that.
#7
Rotary Freak
iTrader: (1)
most likely the ground is faulty or some other bit on the idiot light cluster crapped out on you, if feel you really need it either; test all the circuits, have it sent off to icemark for a rebuild or rip it out and put some real guages in
or if you know someone woth a working swap it over and see if it a faulty cluster or not
or if you know someone woth a working swap it over and see if it a faulty cluster or not
Trending Topics
#8
i still don't know what the problem is. Once the car is on then the lights should be off. i don't get it. I assume it is NOT the same issue DREYKO is having. If it IS then best case scenario the rear harness came off. Go to a junkyard and get another one and test it out.
#9
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes
on
19 Posts
Key to ON...........all the warning lights come on.
Engine started................the only lights on should be if you left the hatch open, door open, emer brake on etc.
No lights on when the key is put to ON????? On a series four, the alternator white/black wire sends a ground to the alt relay in the CPU which in turn puts a gnd on the warning light circuit causing all the warning lights to come on.
Series five is similar but there is no CPU involved.
No lights when the key is to ON????? Possible bad solder joint in the warning light jack. Put the key to ON (series four). PUt a gnd on the WHITE/BLACK wire at the back of the alternator (plug off the alt). The warning lights should all come on.
Still no warning lights???? Pull the plug off the CPU and key to ON. Put a gnd on the wire b/t the CPU and the warning light clusted. See the right wire in the free online diagrams for a series four.
Not a series four? Shoulda said so in the first place.
#10
Yo dawg, Im happy for you
iTrader: (2)
Join Date: Jan 2006
Location: Corvallis, Oregon
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
Damn you bringing this up! I noticed on the ride home tonight that none of my lights were working as well, not even door ajar. They were working yesterday. I will investigate tomorrow
#12
Junior Member
Join Date: Jun 2006
Location: Omaha, Nebraska
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
with you series 4 guys... you need to take out the CPU and look at it. resolder some of the board and put that sucker back in. I had an FB01 CPU in my 87, then swapped out for an FB05 from an 88. the FB01 seem to have problems with soldering in my opinion.
Thread
Thread Starter
Forum
Replies
Last Post
Denholm
2nd Generation Specific (1986-1992)
5
08-07-06 10:21 PM
R_PROWESS
2nd Generation Specific (1986-1992)
2
03-16-06 08:13 PM