ken, could you give me a quick rundown on the connections for the lm1815 please. I'll be putting it together this afternoon. Oh, and I think I've figured out a solution for the extra db-9... use a 7-pin s-video cable instead.

 

haha, I already gave you a rundown of that stuff

it'll have to wait till I get home tonight... I don't have time to look at it before that....

That's the stuff I drilled a couple of small holes in the MS board for.... remember?

If you still don't, take a look at my .txt file at http://www.speakeasy.org/~culverk/wh...oder-howto.txt

I need to go back and edit this thing eventually... but it should be OK until then.

 

yah >_> I remember that there were the 2 signal wires and 2 grounds from the cas (vr1,gnd1,vr2,gnd2) and that output1 goes to pin6 on the 6-pin chip, but I don't remember from there.

*dloads file* If I need any more hints I'll talk to you when you get home.


oh, and I'm going to use an 8-pin appletalk cable for the connections.

 

hey guys and gals...

stilllookin for info on rekeying JUST the ignition cylinder on an FC.. just need the tumbler and the key ... i can do the install myself

anyone know where i can get one and about how much it will run me?

 

i mean i may be way off base...but arent oil coolers finned radiators basically

i mean thats thin to me

i've never MIG welded aluminum so i can say ... but very few people would have a MIG that can do Al welds and make them look nice...

you need an adjustable waveform and reverse polarity if im not mistaken


better safe than sorry, most good shops have a TIG anyways


try RPM Fabrication LLC in Glen Burnie, ask for Harry, tell him Corey, the guy with the v8 rx7 sent ya

 

¡Hola!

I´m in the Dominican Republic, we came into town (a crazy drive down the mountain, for supplies), so I paid for some internet time. These spanish keybords are crazy. The poverty here is aweful, I´m serving in a town called Polo, right neer the border of Hati, high in the mountains.

There is a whole lot of hard labor to be done here too to help administer aid and such to the people living here. Biulding this house is kinda hard too, because we dont have powertools or anything like that. Lots of digging by hand and such. Money is really tight too. everything here is really expensive. (Exept labor)

One of the trucks we are using is awesome, it´s called a Toyota Dyna. It rules.

I´ll tell everyone the full story later, at Fudds or something, I just thought it would be cool to post and let everyone know that I am still alive.

 

the adjustable waveform and reverse polarity is still TIG... Most people use AC when TIG welding aluminum... the adjustable waveform is good for things like out of position welding on just about any metal... it helps avoid things like undercut by periodically reducing the current... allowing the metal to freeze... it's one of the things that helps get that "stacked dimes" look.

I don't remember what DCRP is used for really, I never used it for anything in class... I'll have to look it up in my textbook

for MIG all you need is the proper voltage, proper wire-feed speed, and proper wire-feed system; the spool-gun type works well...

I was just trying to tell people that it's NOT impossible to MIG aluminum, nor is it hard to make it look good.... as long as the metal is thick... a lot of people say that you can't MIG aluminum at all, and that just isn't true. You CAN MIG aluminum, and you CAN make it look good... there might even be people who can do it on thin metal, but I'm not one of them

 

Yay!! You're alive

 

Yey for jason and dominican republic!11

on a side note, i just saw fantastic 4 and...it was okay..it lacked action to me.

 

The fact that you know this means that I missed you. damn.
*note to self = werk on aim*

One speeding, failure to have registration in car, failure to display valid tags, driving a un insured car.

The cop decided to *** rape me. But the good news is that I got a new court date for it, so I can argue that some of them are bogus and that the cop did by no means have to write ALL this **** up for one account of which I was very cooperative and was completely un aware *cough* that my temp tags had expired.

 

ken: I just finished my megasquirt, lemme know when I can come over to fully benchtest it.

(I need to remove the jumpers and mount the crystal properly still)

 

and i dont want people to think i was saying you CANT ...MIG weld Al ... I myself have done it ... but not on something like an oil cooler which is definitely thin AL... better safe than sorry i always say

 

good thing you have the magic crystal in there!, it won't work without the magic crystal of awesomeness from mt. megasquirt!!

(sorry... It's a little early... and I have to work on a saturday )

 

Yeah, I wasn't disagreeing on that... I totally agree that an oil cooler should be tig welded... AND I don't want to be the one doing it...

I was just saying that a lot of people say it's impossible to mig weld aluminum, and that's nothing more than a myth.

 

Leave the jumpers there for now... we can test with them in... Sunday afternoon/evening should be ok... but I have to work early on monday so you can't stay that late.

 

Huh, now why does that sound familiar?....

lol

 

word.. Yah, I can't stay late Sunday either, 'cause summer session starts on Monday.

 

I had un-registered, improper tags, and no insurance, and I got off with just the improper tags, and no points.....

I'm still dealing with that PBJ though... for a stupid "I made a right turn between the hrs of 6:30 and 9:30 when a sign said not to...."

 

I have a court date on thursday (63 in a 45)

and I think my lisence is actually suspended at the moment
(I forgot to pay a dumb ticket I got for not having my front lisence plate)

EDIT: I haven't been accused of a speeding ticket in over 2 years though... so I should be good... maybe

 

Best of luck to you. I have a court date that I"m actually looking forward to on tuesday. I"m looking forward to it because the court is in OC ;-)

I'm making a day trip outa it!

 

I've got Jury Duty on the 12th.... >_<

Wonder if there's a way I can skip it....

 

I didn't return my paperwork when they sent it to me and I've had no repercussions... But if they haul you in, they usually interview you... Just say you believe the white man is the devil and that you believe in the death penalty or something... Be extreme. Get creative.

Hey. When they take you outta work in trade for $40 a day, are you really paid enough to give a ****?

 

Maybe you can apply for conscientious objector status.

 

Ok.... Now can I have that in english?

 

"I've got Jury Duty on the 12th.... >_<
Wonder if there's a way I can skip it...."

yeah when you go their start talking crazy and saying things like guilty as charged 90 days in the slammer for you, Next. Oh yeah and laugh outloud alot and make references to your time in jail