RX7Club.com - Mazda RX7 Forum
Here's a pic from the back, the third brake light is even perfectly centered with the taillight filler panel
Here's a pic from the back, the third brake light is even perfectly centered with the taillight filler panel
0 2016/01/15 13:32:02
This thing had about a half inch of crud on it when i first got it out of a car at the local u-pull-it, which was a few months ago, i cleaned all of the crap off of it when i got it, today when i got it out of my shed, it still stunk like bad gas, i wanted to gag.
This thing had about a half inch of crud on it when i first got it out of a car at the local u-pull-it, which was a few months ago, i cleaned all of the crap off of it when i got it, today when i got it out of my shed, it still stunk like bad gas, i wanted to gag.
0 2016/01/15 16:55:16
Here it is all cleaned up with a walbro fuel pump installed, and the fuel level sending unit removed. Im going to use the fb sending unit, since the car came with a brand new one in the storage bins
Here it is all cleaned up with a walbro fuel pump installed, and the fuel level sending unit removed. Im going to use the fb sending unit, since the car came with a brand new one in the storage bins
0 2016/01/15 16:58:47
Does anyone know what this is, it is leaking. It is about 4-6 inches above the fuel filter. Will i be alright just bypassing it.the send line goes from the tank, through the filter, then pump, and through this piece, and then to the line that runs to the front of the car, i was just going to remove it since I will be running a lot more pressure, and its already leaking. I just want to make sure what is is and does before I do that
Does anyone know what this is, it is leaking. It is about 4-6 inches above the fuel filter. Will i be alright just bypassing it.the send line goes from the tank, through the filter, then pump, and through this piece, and then to the line that runs to the front of the car, i was just going to remove it since I will be running a lot more pressure, and its already leaking. I just want to make sure what is is and does before I do that
0 2016/01/31 13:18:34
This is my 84 12a half bridgeport. Has a bright yellow hood, because when i ported and rebuilt the engine i was too stupid to bolt the hood back on.i figured that it sat lower than the nose of the car, that not toouch air would get under it, wrong, i hit 3rd gear and that damn thing flew about 25 feet into the air.it scared the shit out of me. I guess I'll never do that again
This is my 84 12a half bridgeport. Has a bright yellow hood, because when i ported and rebuilt the engine i was too stupid to bolt the hood back on.i figured that it sat lower than the nose of the car, that not toouch air would get under it, wrong, i hit 3rd gear and that damn thing flew about 25 feet into the air.it scared the shit out of me. I guess I'll never do that again
0 2016/02/15 07:13:19
Made a vent tube out of a piece of brake line and drilled a hole in the fuel pump cover and Welded it in.
Made a vent tube out of a piece of brake line and drilled a hole in the fuel pump cover and Welded it in.
0 2016/02/20 18:18:43
Also these stainless steel braided brake hoses came today
Also these stainless steel braided brake hoses came today
0 2016/02/20 18:20:43
Alao got a hid headlight kit, amd this relay harness
Alao got a hid headlight kit, amd this relay harness
0 2016/02/20 18:21:48
Heres where i got so far, only the top part of the radiator is bolted up, measured where the bottom has to be and how im going to mount it, and how to mount the intercooler and oil cooler
Heres where i got so far, only the top part of the radiator is bolted up, measured where the bottom has to be and how im going to mount it, and how to mount the intercooler and oil cooler
0 2016/02/26 17:38:59
0 2016/02/28 07:54:06
This is basically how it is going to fit, the rotary works kit that i was going to modify and use wouldn't work, i got all of the mounting brackets to work, but the radiator was way too big, i would have to cut a lot of my radiator support, and it still wouldn't work because it would hit the sway bar, this is actually the intercooler from the rotary works kit.if anyone has a fc that wants a vmount kit , let me know
This is basically how it is going to fit, the rotary works kit that i was going to modify and use wouldn't work, i got all of the mounting brackets to work, but the radiator was way too big, i would have to cut a lot of my radiator support, and it still wouldn't work because it would hit the sway bar, this is actually the intercooler from the rotary works kit.if anyone has a fc that wants a vmount kit , let me know
0 2016/02/28 07:55:41
Basically just inserted a large bolt into the larger hole, put on a hose clamp, cut off the head, put some panel bond on the inside of the hole until it was full, and put some on the outside, on the smaller hole i just panel bonded a push in body clip in. Total price, 0.00.
Basically just inserted a large bolt into the larger hole, put on a hose clamp, cut off the head, put some panel bond on the inside of the hole until it was full, and put some on the outside, on the smaller hole i just panel bonded a push in body clip in. Total price, 0.00.
0 2016/03/06 14:36:51
Here is a picture of the new rails installed
Here is a picture of the new rails installed
0 2016/03/20 06:36:55
How they look with the intake back on
How they look with the intake back on
0 2016/03/20 06:38:03
And here is a picture of the new regulator. While putting it back together, i noticed that some how one of the terminals on the intake temp sensor got broken off, so now I have to get another one
And here is a picture of the new regulator. While putting it back together, i noticed that some how one of the terminals on the intake temp sensor got broken off, so now I have to get another one
0 2016/03/20 06:38:23
This is what i came up with to solve the afm mounting problem. I ordered some silicone adapters to move it to in between the radiator and fender apron. This is just to show the basic idea. It will be lower than this
This is what i came up with to solve the afm mounting problem. I ordered some silicone adapters to move it to in between the radiator and fender apron. This is just to show the basic idea. It will be lower than this
0 2016/05/01 17:16:36
Here is how i mounted the intercooler. I liked rhe vmount set up better,bit im dying to drive my car ,and dont want to wait to get custom a/c hoses made
Here is how i mounted the intercooler. I liked rhe vmount set up better,bit im dying to drive my car ,and dont want to wait to get custom a/c hoses made
0 2016/05/01 17:19:54
Here is where i mounted the coils and fuse box
Here is where i mounted the coils and fuse box
0 2016/05/01 17:22:23
Here is another view of how i mounted the intercooler
Here is another view of how i mounted the intercooler
0 2016/05/01 17:24:06
0 2016/05/08 18:50:23
Finished mounting and plumbing my oil cooler and intercooler
Finished mounting and plumbing my oil cooler and intercooler
0 2016/05/08 18:50:37
0 2016/05/08 18:53:18
I also figured out a better way to mounty afm,without it being in the way of anything. It turns out that i couldn't use the stock t.i.d.,i just used a 45degree coupler coming off of the turbo inlet,and it pretty much fit right under the intercooler pipe.plus it looks a hell of a lot cleaner this way
I also figured out a better way to mounty afm,without it being in the way of anything. It turns out that i couldn't use the stock t.i.d.,i just used a 45degree coupler coming off of the turbo inlet,and it pretty much fit right under the intercooler pipe.plus it looks a hell of a lot cleaner this way
0 2016/05/08 18:53:28
0 2016/05/15 08:27:37
Nice and clean now,time to get it wired up
Nice and clean now,time to get it wired up
0 2016/05/15 08:35:47
I just got back from new York ,i picked this set of rims up from i guy there. Thanks roger,i think they look great on there
I just got back from new York ,i picked this set of rims up from i guy there. Thanks roger,i think they look great on there
0 2016/05/15 08:36:41
I also got this in the mail the other day, im not sure whether or not if im going to run the fuel lines through it, im thinking no,because i dont want the gas running through something that is hot, if anyone has experience with one of these, please let me know
I also got this in the mail the other day, im not sure whether or not if im going to run the fuel lines through it, im thinking no,because i dont want the gas running through something that is hot, if anyone has experience with one of these, please let me know
0 2016/05/15 08:38:53
My battery cable came today,hopefully i can finish the wiring this weekend
My battery cable came today,hopefully i can finish the wiring this weekend
0 2016/05/20 11:18:01
I finally figured out what battery im going to use,i got an optima 680 ,a lot of people on here have good things to say about it,this thing is tiny,i could probably mount it in the radio opening if i wanted to
I finally figured out what battery im going to use,i got an optima 680 ,a lot of people on here have good things to say about it,this thing is tiny,i could probably mount it in the radio opening if i wanted to
0 2016/06/19 06:51:10
Also ordered a big brake kit off of ebay.sellers name is hounderville. Very good quality, this is the only picture i took of it so gar,and i forgot it at home.i still have to get all of the fc brake parts to install it, but first im going to take measurements of everything in the kit .
Also ordered a big brake kit off of ebay.sellers name is hounderville. Very good quality, this is the only picture i took of it so gar,and i forgot it at home.i still have to get all of the fc brake parts to install it, but first im going to take measurements of everything in the kit .
0 2016/06/19 06:54:11
Got the ecu,knock control unit, atmosphere pressure sensor installed on the mounting bracket. Im going to use my rtek 1.8 until i get it running good and all of the bugs worked out. Then I'll switch to my rtek 2.1
Got the ecu,knock control unit, atmosphere pressure sensor installed on the mounting bracket. Im going to use my rtek 1.8 until i get it running good and all of the bugs worked out. Then I'll switch to my rtek 2.1
0 2016/06/19 06:58:00
Got the harness ran through the firewall. I know it dont look pretty right now, but i want to make sure i have all of the bugs worked out of it before I wrap the harness and tie it down
Got the harness ran through the firewall. I know it dont look pretty right now, but i want to make sure i have all of the bugs worked out of it before I wrap the harness and tie it down
0 2016/06/19 07:00:58
Here is a picture ofy alternator and coolant and oil pressure sending unit harnesses
Here is a picture ofy alternator and coolant and oil pressure sending unit harnesses
0 2016/06/19 07:05:31
I drilled a hole in the side of the transmission tunnel and put a grommet, and ran a 6 foot piece of 3/4 in. Heater hose through it ,and then ran the power wire tjeough that, dont want to take any chances of something wearing a hole in the insulation of the wire
I drilled a hole in the side of the transmission tunnel and put a grommet, and ran a 6 foot piece of 3/4 in. Heater hose through it ,and then ran the power wire tjeough that, dont want to take any chances of something wearing a hole in the insulation of the wire
0 2016/06/20 10:22:38
Heres how it came out ,its actually a really good fit,and the piece of hose is tje perfect size to make it to the driver storage bin
Heres how it came out ,its actually a really good fit,and the piece of hose is tje perfect size to make it to the driver storage bin
0 2016/06/20 10:26:09
Here is the stock harness removed, i should have never installed it to begin with
Here is the stock harness removed, i should have never installed it to begin with
0 2016/06/21 19:13:12
The engine re wired up again,i am not plugging the iat in until i have everything bolted to the engine, if you look close you can see that one of the tabs is missing on it. that broke off when I installed the stock harness, that little tiny sensor was like $75. I am not breaking another one
The engine re wired up again,i am not plugging the iat in until i have everything bolted to the engine, if you look close you can see that one of the tabs is missing on it. that broke off when I installed the stock harness, that little tiny sensor was like $75. I am not breaking another one
0 2016/06/21 19:14:19
0 2016/06/24 15:45:04
This thing is huge,i have the same one on my tan car,and the temp gauge don't go above 1/4 of the way up
This thing is huge,i have the same one on my tan car,and the temp gauge don't go above 1/4 of the way up
0 2016/06/24 15:45:27
This is the fan that came with it,im not sure if im going to use rhis one or the one tjat came with my other radiator, that one has an aluminum shroud on it tjat fits perfectly on the radiator
This is the fan that came with it,im not sure if im going to use rhis one or the one tjat came with my other radiator, that one has an aluminum shroud on it tjat fits perfectly on the radiator
0 2016/06/24 15:46:48