RX7Club.com - Mazda RX7 Forum
Another picture with the suspension back in , new swqy bar links installed
Another picture with the suspension back in , new swqy bar links installed
0 2015/10/18 10:35:28
Here is a picture of the freshly painted suspension back in
Here is a picture of the freshly painted suspension back in
0 2015/10/18 12:36:39
Here it is with the new sway bar links installed
Here it is with the new sway bar links installed
0 2015/10/18 12:40:25
I made a couple copies of my racing beat heat shield
I made a couple copies of my racing beat heat shield
0 2015/10/22 10:08:24
0 2015/10/23 14:26:47
Here's a pic of the driver's side back in, I think it looks pretty good with the springs painted the same color as the car
Here's a pic of the driver's side back in, I think it looks pretty good with the springs painted the same color as the car
0 2015/11/01 14:06:44
I went to put the new clutch on , and noticed that there is nothing left of the pilot bearing, luckily my clutch came with one, but not a new grease seal for it
I went to put the new clutch on , and noticed that there is nothing left of the pilot bearing, luckily my clutch came with one, but not a new grease seal for it
0 2015/11/01 14:08:48
It took about 2 hour's to cut and chisel this damn thing out , it was seized in there
It took about 2 hour's to cut and chisel this damn thing out , it was seized in there
0 2015/11/01 14:11:05
After waiting 3 days for the new pilot bearing seal, I was finally able to finish putting the clutch on
After waiting 3 days for the new pilot bearing seal, I was finally able to finish putting the clutch on
0 2015/11/01 14:12:29
This is the to4b that I was telling you about, just sitting on the manifold
This is the to4b that I was telling you about, just sitting on the manifold
0 2015/11/01 16:08:44
Plenty of room
Plenty of room
0 2015/11/01 16:10:02
Therenis a ton of room, it just looks like I'll have to make a heat shield in between the turbo and intake manifold
Therenis a ton of room, it just looks like I'll have to make a heat shield in between the turbo and intake manifold
0 2015/11/01 16:10:36
You will know if its the same one that I found on there, because it will have which looks like some kind of adapters, and a wastegate dump tube in the picture
You will know if its the same one that I found on there, because it will have which looks like some kind of adapters, and a wastegate dump tube in the picture
0 2015/11/02 14:46:12
I won this on ebay the other day, just picked it up tonight
I won this on ebay the other day, just picked it up tonight
0 2015/11/04 17:55:00
I picked this up from eBay a couple of days ago, I just picked it up tonight. 85 GSL, with 79 wheels with brand new tires on it, it runs great and came with some new parts
I picked this up from eBay a couple of days ago, I just picked it up tonight. 85 GSL, with 79 wheels with brand new tires on it, it runs great and came with some new parts
0 2015/11/04 19:33:26
Herr they are finally bolted together
Herr they are finally bolted together
0 2015/11/07 17:51:03
And I also got them back in the car
And I also got them back in the car
0 2015/11/07 17:52:38
0 2015/11/07 17:54:02
Now I just have to figure out how im going to fabricate a transmission mount. It doesn't look like it's going to be too hard
Now I just have to figure out how im going to fabricate a transmission mount. It doesn't look like it's going to be too hard
0 2015/11/07 17:54:56
The wastegate that I ordered for the to4b that I have came this weekend, I ordered the wrong size, I thought I needed a 46mm, it turns out that I need a 50mm.does anyone know if they make adapters to change sizes, or will I have to make one
The wastegate that I ordered for the to4b that I have came this weekend, I ordered the wrong size, I thought I needed a 46mm, it turns out that I need a 50mm.does anyone know if they make adapters to change sizes, or will I have to make one
0 2015/11/08 19:08:36
Im pretty happy with how it turned out. Up next is the radio surround
Im pretty happy with how it turned out. Up next is the radio surround
0 2015/11/09 13:30:38
I don't think it came out too bad for my first time using it, next up, the spare radio surround that I have
I don't think it came out too bad for my first time using it, next up, the spare radio surround that I have
0 2015/11/09 17:50:52
Here is the mount, just a simple square tube 3/4 inch thick, and i drilled holes in the crossmember to match the holes in the transmission, i just have to get 2 longer bolts to go through everything, then i can bolt up the driveshaft
Here is the mount, just a simple square tube 3/4 inch thick, and i drilled holes in the crossmember to match the holes in the transmission, i just have to get 2 longer bolts to go through everything, then i can bolt up the driveshaft
0 2015/11/30 17:15:04
I also put the headlights and the front nose panel back on so i can start mounting the vmount
I also put the headlights and the front nose panel back on so i can start mounting the vmount
0 2015/11/30 17:18:17
Here is a picture of the vmount setup
Here is a picture of the vmount setup
0 2015/11/30 17:19:43
Here it is installed, it was really easy to make
Here it is installed, it was really easy to make
0 2015/12/01 09:57:43
This shows the difference in where the bolt holesare situated, just had to ream both holes outward a little bit
This shows the difference in where the bolt holesare situated, just had to ream both holes outward a little bit
0 2015/12/01 09:58:35
Heres a picture of the driveshaft mounted
Heres a picture of the driveshaft mounted
0 2015/12/27 19:55:59
0 2015/12/27 19:57:03
I also started figuring out the vmount setup. I figured out how it gets mounted .all i have to do is make a few brackets, and it should bolt right up
I also started figuring out the vmount setup. I figured out how it gets mounted .all i have to do is make a few brackets, and it should bolt right up
0 2015/12/27 19:57:43
Also this came today, mtxl wideband
Also this came today, mtxl wideband
0 2016/01/08 19:27:40
That is just how they would be bolted up in the fender, hope this helps
That is just how they would be bolted up in the fender, hope this helps
0 2016/01/11 13:47:40
If you look closely you can see how i have the cable routed, it goes behind the alternator
If you look closely you can see how i have the cable routed, it goes behind the alternator
0 2016/01/14 20:34:31
And out on top of the turbo, and up and around the intake manifold and then bolted to the bracket, and then the throttle body. Can someone please tell me if this is how it is supposed to be routed.
And out on top of the turbo, and up and around the intake manifold and then bolted to the bracket, and then the throttle body. Can someone please tell me if this is how it is supposed to be routed.
0 2016/01/14 20:36:19
Heres a picture of how bad the clutch master cylinder was leaking, anybody know what I can use to clean the inside of the firewall where it was leaking
Heres a picture of how bad the clutch master cylinder was leaking, anybody know what I can use to clean the inside of the firewall where it was leaking
0 2016/01/14 20:39:50
Here's a pic of the whole new clutch hydraulic system installed
Here's a pic of the whole new clutch hydraulic system installed
0 2016/01/14 20:41:48
This just came today, the correct battery harness, now I can concentrate on the wiring
This just came today, the correct battery harness, now I can concentrate on the wiring
0 2016/01/15 12:43:29
This is just sitting on there , it actually fits really good, clears the hatch, and power antenna
This is just sitting on there , it actually fits really good, clears the hatch, and power antenna
0 2016/01/15 13:23:00
Heres how it looks from the bac, i can't figure out how to enlarge the pictures when you upload them, sorry for the far away shot
Heres how it looks from the bac, i can't figure out how to enlarge the pictures when you upload them, sorry for the far away shot
0 2016/01/15 13:25:44
Since it was black, i would see how it fit on the 7, here's how it looks from the side, its just taped down. It actually fits really well, the hatch clears it, as well as the power antenna
Since it was black, i would see how it fit on the 7, here's how it looks from the side, its just taped down. It actually fits really well, the hatch clears it, as well as the power antenna
0 2016/01/15 13:30:00