I will prob be in for a set of lights for my FB once I get my FD lights and install them since it will be night and day between them.

 

http://www.youtube.com/watch?v=LpADeP-Vg0M
http://www.youtube.com/watch?v=j-i1MsVXFaA

I figure if it takes a bat and a good solid whack to shatter the glass, minor pebbles off the highway shouldn't hurt this laminate.

 

how much would the deposit be?

 

full price of the lights unless we make special arrangements. We tried partial payments for another GB but it resulted in a total mess trying to deal with each persons individual timing and reason why they were going to pay the remainder but couldn't yet, but still wanted the lights. It just ended up being alot of overhead to deal with unfortunately. If you have some extenuation circumstance I'm willing to try to work with you but for the most part we just need all payments in full up front (so start saving ) .

The other reason is that we need to buy the parts for all of the kits in large quantities up front, and we dont have the tens of thousands required to front for all the parts needed (the parts to construct these are not cheap) . For other items like our oil cooler kits (where we stock all of the little parts but order the cores directly after the order is placed) a system with small deposits works, but since the lights need to be purchased in full and assembled that setup doenst work out so well. Thanks for asking... I hadn't talked about that yet.
-Heath

 

full price of the lights unless we make special arrangements. We tried partial payments for another GB but it resulted in a total mess trying to deal with each persons individual timing and reason why they were going to pay the remainder but couldn't yet, but still wanted the lights. It just ended up being alot of overhead to deal with unfortunately. If you have some extenuation circumstance I'm willing to try to work with you but for the most part we just need all payments in full up front (so start saving ) .

The other reason is that we need to buy the parts for all of the kits in large quantities up front, and we dont have the tens of thousands required to front for all the parts needed (the parts to construct these are not cheap) . For other items like our oil cooler kits (where we stock all of the little parts but order the cores directly after the order is placed) a system with small deposits works, but since the lights need to be purchased in full and assembled that setup doenst work out so well. Thanks for asking... I hadn't talked about that yet.
-Heath

<input id="gwProxy" type="hidden"><!--Session data--><input onclick="jsCall();" id="jsProxy" type="hidden">

 

get me a roll of that! im sure for a few extra bones most people would pony up for a couple squares of that stuff to protect their lights
<input id="gwProxy" type="hidden"><!--Session data--><input onclick="jsCall();" id="jsProxy" type="hidden">

 

i need some glass like that at my houes!

 

1.) Kerebrus - FB
2.) Whitey85mtu - FB
3.) Thunkrd - FB
4.) BurntOrangeT2 - FC
5.) Fonzi581- FC
6.) Pele - FC / Universal 6054 (Two sets)
7.) Akagis_White_Comet - FC
8.) Hozzmanrx7 - FC
9.) MaczPayne - FC
10.) lemursama - FC
11.)FC3S1991- FC
12) darksider415 - FC
13.) RX710thAE - FC

 

We are soo close but yet still so far away from getting these produced.

 

why am i not on this list?


lets try this again..

therealmogwai 1987 t2

 

1.) Kerebrus - FB
2.) Whitey85mtu - FB
3.) Thunkrd - FB
4.) BurntOrangeT2 - FC
5.) Fonzi581- FC
6.) Pele - FC / Universal 6054 (Two sets)
7.) Akagis_White_Comet - FC
8.) Hozzmanrx7 - FC
9.) MaczPayne - FC
10.) lemursama - FC
11.) FC3S1991- FC
12.) darksider415 - FC
13.) RX710thAE - FC
14.) therealmogwai - FC

updated list.

 

I'm really tempted to sign up but I think I will wait a little bit longer and see how the sign ups progress.

Edit: Only 15? I will definately sign up for these if they go into production -- don't want to miss out!

 

Yes, 15 minimum for FC or FB. unfortunately the FB ones seem to have even less interest than the FC lights.

 

I'll be in for a set for a FB. if it happens

 

ill be in on a set for the fc if you collect payment anytime after may

 

I would like to sign up for this item. After receiving a SUPER high quality oil cooler kit I must now have these lights! Please put me down for a set! Thank you very much guys!

 

You guys need to use the list and organize cause its too hard to track people w/out it

1.) Kerebrus - FB
2.) Whitey85mtu - FB
3.) Thunkrd - FB
4.) BurntOrangeT2 - FC
5.) Fonzi581- FC
6.) Pele - FC / Universal 6054 (Two sets)
7.) Akagis_White_Comet - FC
8.) Hozzmanrx7 - FC
9.) MaczPayne - FC
10.) lemursama - FC
11.) FC3S1991- FC
12.) darksider415 - FC
13.) RX710thAE - FC
14.) therealmogwai - FC

Also, If you got oil coolers from us then you must have an FD, and if so there is another thread for the FD lights

https://www.rx7club.com/vendor-classifieds-276/gb-bi-xenon-hid-projector-sakebomb-garage-867943/
<input id="gwProxy" type="hidden"><!--Session data--><input onclick="jsCall();" id="jsProxy" type="hidden">

 

Opps my apologies. Got excited and wasn't looking at which one this was hahaha

 

so would we need 15 members for each type of molds? Like 15 for the FB and 15 for the FC?

 

1.) Kerebrus - FB
2.) Whitey85mtu - FB
3.) Thunkrd - FB
4.) BurntOrangeT2 - FC
5.) Fonzi581- FC
6.) Pele - FC / Universal 6054 (Two sets)
7.) Akagis_White_Comet - FC
8.) Hozzmanrx7 - FC
9.) MaczPayne - FC
10.) lemursama - FC
11.) FC3S1991- FC
12.) darksider415 - FC
13.) RX710thAE - FC
14.) therealmogwai - FC
15.)2gslse - FB

 

I'd love to have a pair of these. But at the moment and near future I'll have to live with my sub-standard lighting.

 

Yeah either or . Looks like we are getting close to having enough interest to make the FC ones happen, assuming that not too many people drop out. I'll start the process of getting the prototype ready to have molds made, though we still need more people on this to actually go through with producing them... I also need to get a local FC guy in the bay area to test fit these before its a complete go, as we may need to include longer headlight adjustment screws since these are significantly deeper than the stock lights.

If FB is gonna happen we're gonna need a lot more people in on it for sure. I'm gonna separate out the two lists so it's a little more organized. Please add to the following updated list.

FC

1. BurntOrangeT2 - FC
2. Fonzi581- FC
3. Pele - FC / Universal 6054 (Two sets)
4. Pele - FC / Universal 6054 (Two sets)
5. Akagis_White_Comet - FC
6. Hozzmanrx7 - FC
7. MaczPayne - FC
8. lemursama - FC
9. FC3S1991- FC
10. darksider415 - FC
11. RX710thAE - FC
12. therealmogwai - FC
13.
14.
15.


FB
1. Kerebrus - FB
2. Whitey85mtu - FB
3. Thunkrd - FB
4. 2gslse - FB
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.

 

I really want to put my name on the list... Money, its a bitch.

 

Couldn't agree more.

 

Not to crap on this and maybe I'm over looking something. I decided for the hell of it I would google '6054 projector' and I found that these are already made. I would assume that they should fit just the same too but perhaps space is too limited. Price is in the 800 range. though I did find one for 599. That may have only been one side though.

http://www.kbcarstuff.com/6054_200mm..._p/xd-6054.htm
http://www.streetbeatcustoms.com/rectangle.html

Any feedback?
If this goes against anything sorry I wasn't trying to kill the GB only offer the possible alternative in case it falls through.