Mac's FC "Build" Thread
01-16-12, 11:46 PM
#328
Full Member
Join Date: Jun 2011
Location: NJ
Posts: 246
Likes: 0
Received 0 Likes
on
0 Posts
Also, to all the Taurus alt acolytes. There's nothing wrong with a properly functioning FD alt (especially when upgrading from the craptastic s4 alt). The FD alt does "turn on" , but that happens at 3,000 rpm, not 6 grand, so if thats the case, either the belts were lose, the alt was bad, or it was wired incorrectly. My FD alt charges at 14.2 volts even below 3k rpm once the car has been running, and has done so for the last 4 years (and I bought it used). I have nothing against cheap an effective mods but if you have a working FD alt, theres no reason to jump ship. And lets be honest, the Taurus alt while effective, is ugly 
:
:
01-17-12, 01:28 AM
#329
I believe he was exaggerating the point of revving to 6k, but regardless waiting for the fd alt to turn on is a bit inconvenient. I also have an fd alt and when keeping the revs low or at idle, its a struggle to keep above 13 volts with lights, heat, radio etc. at idle with all loads on it can barely handle it, so why waste time with it risking killing a battery or worst, when there's a cheap fix.
01-17-12, 10:11 AM
#330
Full Member
Join Date: Jun 2011
Location: NJ
Posts: 246
Likes: 0
Received 0 Likes
on
0 Posts
oh wow then that's crazy, hows that Taurus alt holding out for you? any problems with it so far? i got a completely rebuilt one coming in the mail. got it for $40 off of ebay.
01-17-12, 02:15 PM
#331
Taurus alt is ok, I think I may need to do some rewiring though. My headlights dim when idle drops to around 600rpms. I'll keep toying with it later, as for now just trying to finish my TII hood so that I can start working on my video that my buddy has been bothering me about.
lol
01-18-12, 08:37 PM
#334
finally got a hood! sweet.
try cutting the heat shield on the bottom of your ic. some guy on here claimed that his intake temps dropped 15 degrees.
when you ported your turbine housing did you change the flappers to a larger one? it might help more with your boost creep.
try cutting the heat shield on the bottom of your ic. some guy on here claimed that his intake temps dropped 15 degrees.
when you ported your turbine housing did you change the flappers to a larger one? it might help more with your boost creep.
Last edited by LoLsmileyFC; 01-18-12 at 08:46 PM.
01-20-12, 12:13 PM
#335
Yep thats the guy, were trying to get a look for my car that will stick around for a while. I don't wanna shoot the vid and then change my look completely again.
It may just be my belts are loose, I didn't make an extended bracket like suggested.
Hmm..I'll look more into the heat shield thing. As for the flapper its a s4 turbo and I ported it according to the stock flapper.
finally got a hood! sweet.
try cutting the heat shield on the bottom of your ic. some guy on here claimed that his intake temps dropped 15 degrees.
when you ported your turbine housing did you change the flappers to a larger one? it might help more with your boost creep.
try cutting the heat shield on the bottom of your ic. some guy on here claimed that his intake temps dropped 15 degrees.
when you ported your turbine housing did you change the flappers to a larger one? it might help more with your boost creep.
01-20-12, 01:24 PM
#336
iRussian
iTrader: (3)
Join Date: Oct 2006
Location: midwest IL, USA
Posts: 947
Likes: 0
Received 0 Likes
on
0 Posts
What you can also do is to port it out so it's bigger than the flapper, and weld a washer to the flapper to make it seal. I did it and it worked great, held 5 psi w/ bonez cat and 8psi no boost controller w/ straight pipe.
Thread *****: I have an RTEK 1.7 I can sell you if you want one BTW, I went HALTECH on my ****.
Thread *****: I have an RTEK 1.7 I can sell you if you want one BTW, I went HALTECH on my ****.
01-20-12, 03:20 PM
#337
back to wire tuck
IMAG0033.jpg?t=1322107218
this is how i did mine. i think going through the upper frame rail looks a bit better than just zip ties
IMAG0033.jpg?t=1322107218
this is how i did mine. i think going through the upper frame rail looks a bit better than just zip ties
01-23-12, 01:00 AM
#340
back to wire tuck
http://i32.photobucket.com/albums/d5...g?t=1322107218
this is how i did mine. i think going through the upper frame rail looks a bit better than just zip ties
http://i32.photobucket.com/albums/d5...g?t=1322107218
this is how i did mine. i think going through the upper frame rail looks a bit better than just zip ties
Thanks man, the rear bumper is a GP Sports replica.
01-23-12, 01:44 PM
#345
I got it from a local seller, he sold me the rear and front bumper. I can't say who made the replica but it seems like good quality.
From yesterday:
Its fun being the only fc that rolls to events like this..."So You Think You Can Stance"
http://www.motormavens.com/2012/01/s...-fatlace-meet/
