1994 JDM Build Thread
#176
Senior Member
Thread Starter
Start of fuel filter relocation
Starting to relocate my fuel filter. I will use the holes in the rear subframe. To mount a custom plate where the fuel filter and water meth pump will be mounted. I will use the existing holes in the subframe. I didn’t want to put just a long bolt through so I made a spacer which will be bolted from the front so I have a thread in the rear.
#177
Senior Member
Thread Starter
Making a fuel filter relocation and water meth pump mount
first rough prototype that I cut with my dad out of some material that I had left over . Next step is to make it out of 5mm Aluminium and remove all the material I don’t need to make It look neater
The following users liked this post:
EREBUS (05-10-22)
#178
Senior Member
Thread Starter
Mounting the RX8 Condenser
My dad made me some spacers to mount a RX8 Aircon condenser with the built in dryer bottle onto my radiator. I decided to use the OEM mounting points as it’s just easier to replace should it break
Widened the OEM holes so I could insert some rubber spacers and cut off the brackets a bit so they flush with the radiator edges
Mock-up
Aluminium spacers welded onto the radiator
Test fit with the intercooler
Widened the OEM holes so I could insert some rubber spacers and cut off the brackets a bit so they flush with the radiator edges
Mock-up
Aluminium spacers welded onto the radiator
Test fit with the intercooler
Last edited by Markus1981; 05-10-22 at 03:27 PM.
The following 2 users liked this post by Markus1981:
EREBUS (05-10-22),
estevan62274 (05-12-22)
#179
Senior Member
Thread Starter
Fuel filter and water meth pump bracket
Decided to make the top square and a little bit higher
The thread inside lets me bolt it from the back and leaves me with a nice thread that I can mount a nut on without having to hold it on the diff side to counter
Mounted without the pump and fuel filter
This is how the fuel filter and water meth pump will be mounted . Bracket will be powder coated in black to have be less visible . Eventually I will fit a better filter but running out of money and want to get the car running
#180
That is really nice
The following users liked this post:
Markus1981 (05-22-22)
#182
Senior Member
Thread Starter
Redesigning the IGN1A Bracket
Spent the last 2 days making a new mount for the IGN1A coils . I decided I wanted to mount them on the frame rails but didn’t like the available options that where out there so I designed my own . I made sure I can remove the screws of the mounting plate even when the coils are assembled onto the bracket . Another design consideration was beeing able to remove the coils without having to remove the mounting plates .This design will probably only fit RHD cars as on LHD cars probably the steering colum will be in the way . I used existing holes in the frame rail , the top one already has a thread from factory , the other two will be done with rivet nut inserts into the existing holes. This will be made from one piece of solid aluminum.
CAD design
Complete assembly
Test 3d Print to see if all the holes line up and to see if there are any clearance issues
Mock-up of the rear coils
CAD design
Complete assembly
Test 3d Print to see if all the holes line up and to see if there are any clearance issues
Mock-up of the rear coils
The following users liked this post:
estevan62274 (02-20-23)
#184
Senior Member
Thread Starter
Brand new OEM a Mazda Parts arrived from Japan
All Brand new OEM Parts arrived from Japan . Center arm rest , spirit a shift know and brand new map pocket 🤩
The following 2 users liked this post by Markus1981:
estevan62274 (02-20-23),
GtiKyle (07-08-22)
#185
Senior Member
Thread Starter
Finally some updates
So it’s been a while and work has been hectic. Spent the weekend building the engine harness . I am almost finished with it just waiting for some more connectors to arrive
That’s how far I am now . Just need to figure out where to mount the FPR / MAP sensor / boost solenoid / oil pressure sensors
That’s how far I am now . Just need to figure out where to mount the FPR / MAP sensor / boost solenoid / oil pressure sensors
The following 2 users liked this post by Markus1981:
estevan62274 (02-20-23),
Snipe G (02-28-23)
#186
Rotary Enthusiast
I just wanted to say this is a very 😎 build!
#188
Senior Member
Thread Starter
Not many updates to report. Time is my biggest issue. Designed a 3D printable bracket for the battery fuse box. That is clamped against the Fusebox on the dome. I made it free to download on thingyverse
https://www.thingiverse.com/thing:6163851
https://www.thingiverse.com/thing:6163851
Thread
Thread Starter
Forum
Replies
Last Post