3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Sudden loss of power, Extremely loud exhaust

Old Feb 22, 2018 | 07:01 PM
  #1  
staples323's Avatar
Thread Starter
Bubble Chaser
 
Joined: Dec 2015
Posts: 51
Likes: 0
From: Suffolk, U.K.
Exclamation Sudden loss of power, Extremely loud exhaust

While driving home from work tonight, merging onto the highway, the car suddenly lost power and became extremely loud. Was around 6k RPM and pretty close to full throttle, having a little fun with the on ramp that I'm now regretting.

Off throttle sounds perfectly normal. Any amount of gas sounds like a tractor and accelerates about as quickly and stalls with clutch in.

Fearing the worse (blown motor) but wanted to see if there's anything else I should check this weekend as it is 1am here and I cant do any troubleshooting tonight.
Reply
Old Feb 22, 2018 | 08:12 PM
  #2  
kensin's Avatar
Put it in the microwave!
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (22)
 
Joined: Jul 2009
Posts: 1,568
Likes: 35
From: CA
Open the hood and check your map sensor line
i believe its popped off
Reply
Old Feb 23, 2018 | 07:17 AM
  #3  
staples323's Avatar
Thread Starter
Bubble Chaser
 
Joined: Dec 2015
Posts: 51
Likes: 0
From: Suffolk, U.K.
Originally Posted by kensin
Open the hood and check your map sensor line
i believe its popped off
The map line is connected though the green/yellow wire on the connector looks pretty dodgy, I may have a short.
Reply
Old Feb 23, 2018 | 07:39 AM
  #4  
Brodie121's Avatar
Rotary Enthusiast
Tenured Member 10 Years
iTrader: (8)
 
Joined: Oct 2009
Posts: 848
Likes: 7
From: BC, Canada
He means the actual vacuum line going from intake manifold to map sensor. they like to pop off from boost.
Reply
Old Feb 23, 2018 | 07:46 AM
  #5  
Molotovman's Avatar
Ban Peak
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (50)
 
Joined: Jul 2002
Posts: 4,250
Likes: 550
From: Northern Virginia
Agreed on the map sensor vacuum line. Have you looked things over in the light?
Reply
Old Feb 23, 2018 | 08:05 AM
  #6  
DaleClark's Avatar
RX-7 Bad Ass
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (56)
 
Joined: Jan 2002
Posts: 15,622
Likes: 2,725
From: Pensacola, FL
Yep, start with the easy stuff. If nothing is panning out, you may want to post a video of starting the car, idling, and revving so we can hear it.

Compression check is a good next step, you can easily do this with a parts store tester and that will tell you if the engine is good or not. If it is good, keep troubleshooting, if not, make plans for the engine.

Dale
Reply
Old Feb 23, 2018 | 09:51 AM
  #7  
staples323's Avatar
Thread Starter
Bubble Chaser
 
Joined: Dec 2015
Posts: 51
Likes: 0
From: Suffolk, U.K.
Originally Posted by Brodie121
He means the actual vacuum line going from intake manifold to map sensor. they like to pop off from boost.
Connected to sensor and manifold though I wasn't able to see if the line itself had a hole or not.

Will compression check this weekend and continue the troubleshooting
Reply
Old May 4, 2018 | 09:04 AM
  #8  
staples323's Avatar
Thread Starter
Bubble Chaser
 
Joined: Dec 2015
Posts: 51
Likes: 0
From: Suffolk, U.K.
After being sent off out of country for a bit I finally had time to get a video.


It's not looking good. Any help is apprciated.
Reply
Old May 4, 2018 | 09:12 AM
  #9  
staples323's Avatar
Thread Starter
Bubble Chaser
 
Joined: Dec 2015
Posts: 51
Likes: 0
From: Suffolk, U.K.
Here is another vid
Reply
Old May 10, 2018 | 05:17 AM
  #10  
jack_am's Avatar
Full Member
 
Joined: Feb 2018
Posts: 59
Likes: 0
From: England
Whip the plugs out and do a chuff test. Are you a member of the UK FD Facebook group? There are a few guys doing mobile compression tests if you post up on there.
Reply
Old May 10, 2018 | 10:08 AM
  #11  
Smokey The Talon's Avatar
Long time on-looker
Tenured Member: 20 Years
Liked
iTrader: (33)
 
Joined: Oct 2005
Posts: 886
Likes: 50
From: Columbus, OH
If it got stupid loud and would no longer build boost that could have been an exhaust gasket between the turbos and manifold blowing out. I’ve been there for sure but only while tracking it hard. Would be unusual for a street car to do that.

Also possibly the turbo actuator on the manifold fell off or failed leaving the flapper open on the secondary turbos. Would cause more exhaust noise and slow response. Would still eventually build boost though.

As as others have mentioned do the basic compression test to rule out broken seals first.
Reply
Old May 10, 2018 | 11:08 AM
  #12  
Fritz Flynn's Avatar
All out Track Freak!
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (263)
 
Joined: Jul 2001
Posts: 10,672
Likes: 413
From: Charlottesville VA 22901
Hard to tell in the 1st vid if there's an exhaust leak but that's a lot of smoke and it's idling high.

In the second vid an exhaust leak sound is a possibility and possibly it's the lower intake manifold gasket which would also raise the idle. When the turbo manifold gasket goes enough to affect boost it's a major exhaust leak sound even at idle.
Reply
Old May 10, 2018 | 07:20 PM
  #13  
DaleClark's Avatar
RX-7 Bad Ass
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (56)
 
Joined: Jan 2002
Posts: 15,622
Likes: 2,725
From: Pensacola, FL
Do a compression test before anything else. If the motor is good, go from there.

Dale
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Hazard15301
2nd Generation Specific (1986-1992)
7
May 12, 2018 11:30 PM
Denholm
2nd Generation Specific (1986-1992)
5
Dec 3, 2005 04:33 AM
Jinx099
1st Generation Specific (1979-1985)
7
Feb 9, 2005 11:15 PM
BrianVFR
2nd Generation Specific (1986-1992)
13
Apr 6, 2003 03:11 AM
FlyGuy2000
2nd Generation Specific (1986-1992)
4
Aug 21, 2001 01:04 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 04:27 PM.