3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

not getting boost till 4200

Thread Tools
 
Search this Thread
 
Old Apr 26, 2003 | 10:41 PM
  #1  
Thread Starter
Senior Member
Tenured Member: 20 Years
iTrader: (3)
 
Joined: Mar 2003
Posts: 270
Likes: 3
From: slc, ut
not getting boost till 4200

not getting boost until i get to about 4000 rpm's. usually i feel it kick in about 3200 rpm's then all of a sudden it just started kicking in late. vacuum hoses and check valves are all ok. also blow off valve doesn't release as much air and is quieter.
Reply
Old Apr 27, 2003 | 12:24 AM
  #2  
Batmobile's Avatar
Rotary Enthusiast
Tenured Member 05 Years
 
Joined: Jan 2002
Posts: 782
Likes: 0
From: Los Angeles
Ok....so what is it that you want to buy or sell? Just kidding! I used to live in Salt Lake City also, right next to Raging Waters. Check the usual y-piping, see if there any major leaks from the turbos, check the IC hoses. In my case, on of my solenoids were bad. Good Luck.

uhmmm....This thread is in the wrong section bud. You need to place this in the 3rd Gen Specific.
Reply
Old Apr 27, 2003 | 04:12 AM
  #3  
r0t0r-rooter's Avatar
call me Smokie Smokerson
Tenured Member 10 Years
 
Joined: Aug 2002
Posts: 1,665
Likes: 0
From: Southern California
Do you have a gauge?
If so, what does it say?
Reply
Old Apr 27, 2003 | 06:23 AM
  #4  
rxrotary2_7's Avatar
Lives on the Forum
Tenured Member 20 Years
 
Joined: May 2001
Posts: 5,097
Likes: 1
From: southern NJ
moving out of FS section.
Reply
Old Apr 27, 2003 | 09:08 AM
  #5  
airn's Avatar
Senior Member
Tenured Member: 20 Years
 
Joined: Mar 2002
Posts: 480
Likes: 0
From: nj, McGuire AFB
i the same kind of problem check that your double throtle insnt staying shut.
Reply
Old Apr 27, 2003 | 10:40 PM
  #6  
Thread Starter
Senior Member
Tenured Member: 20 Years
iTrader: (3)
 
Joined: Mar 2003
Posts: 270
Likes: 3
From: slc, ut
don't have a boost guage. sorry kind of a newb question but where is the dobble throttle located. is it on the rest of the throttle stuff by the manifold. if it is which part of that area is it located?
Reply
Old Apr 27, 2003 | 10:51 PM
  #7  
Thread Starter
Senior Member
Tenured Member: 20 Years
iTrader: (3)
 
Joined: Mar 2003
Posts: 270
Likes: 3
From: slc, ut
also fogot to mention, only kicking in late in 1st gear
Reply
Old Apr 28, 2003 | 02:56 AM
  #8  
Junior Member
Tenured Member 05 Years
 
Joined: Feb 2003
Posts: 38
Likes: 0
From: Glendale
hmm....something is not telling the charge relief valve(the butterfly like thing in the ypiping) to open up. No...thats wrong...have a shop test the solenoids under the uim. If its not any of those, I hope your Primary Turbo isn't toast. Do you see any leaks?

Last edited by FD3SDUDE; Apr 28, 2003 at 03:05 AM.
Reply
Old Apr 28, 2003 | 05:44 AM
  #9  
airn's Avatar
Senior Member
Tenured Member: 20 Years
 
Joined: Mar 2002
Posts: 480
Likes: 0
From: nj, McGuire AFB
down load the shop manuel you will need it.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
24seven_dada
3rd Generation Specific (1993-2002)
20
Nov 10, 2018 12:03 PM
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
Bauer778
3rd Generation Specific (1993-2002)
10
Nov 4, 2015 04:42 PM
risingsunroof82
1st Generation Specific (1979-1985)
22
Sep 22, 2015 01:20 PM
Monsterbox
Adaptronic Engine Mgmt - AUS
5
Sep 11, 2015 03:29 PM




All times are GMT -5. The time now is 07:02 AM.