hey Everyone,

Sorry to bring this up but i'm currently re-building my motor & plan on going SINGLE , and like others before me spending $550-650 on a kit to end up with a lot of left over parts is what i want to avoid.

so can those who have good knowledge please help me cross off items that are not going to be needed to in this type of build.

I'm sure this thread can be used as a reference to those after me to save as much $$$ as possible for other useful parts.

based on Atkins website here is the OEM 93-95 Rx7 Gasket Kit Part# 8DFE-10-271B

and what Kit included and individual part #s:

N3A1-13-111 Lower Intake Gasket
N3A1-13-112 Upper Intake Gasket
N3A1-15-116 W/P Housing Gasket
N386-15-162 Water Pump Gasket
N3YA-10-427 Oil Pan Gasket
N3A1-10-502 Front Cover Gasket
N3A1-13-461 Exhaust Gasket
RF36-40-305 Exhaust Gasket
N3A1-13-710 Turbo Gasket
N3A2-13-710 Turbo Gasket
N3B7-13-491 Turbo to Downpipe
0810-14-171 Oil Pick Up Tube
N3C1-15-173 Thermostat O-Ring
N3A1-13-712 Turbo to Intake Gasket
N3A2-14-293 Turbo Oil Drain
N3A1-14-293 Turbo Drain Gasket
N386-13-535 Water Inlet Turbo
N390-14-602 OMP Crush Washer
N3A1-10-424 Oil Fill Tube O-Ring
9956-20-800 OMP Crush Washer
9956-21-000 Oil Injector Washer
9956-21-400 Oil Line Crush Washers
9956-21-800 Oil Cooler Crush Washers
N326-10-B71 Water Jacket Seals
N326-10-B72 Water Jacket Seals
0839-10-455 Tension Bolt Seals
N350-14-604 OMP O-Ring
0813-10-555 Rear Gear O-Ring
N3A1-10-B73 Dowel Pin Rings
N231-10-174 Front Cover O-Ring
N326-10-C15 Front Cover Teflon Ring
NF01-13-ZG3 Lower Injector Grommet
NF01-13-ZG4 Upper Injector Grommet
9954-10-1105 Front Hub Bolt O-Ring
9954-10-1601 Oil Filter Stand O-Rings
9954-10-1252 Diffuser O-Rings
9954-20-5005 Y-Pipe O-Ring

 

I see a lot of twin turbo gaskets on that list but no apex seals, side seals, corner seals, springs for the above, etc. It is usually more cost effective to but a basic gasket kit and piece together the rest of the stuff. Also, some of those kits come with 2nd gen spring unless you specify what you want. I only use the fd NF-01 side seal and corner seal springs. They have inconel content and are much more heat resistant than the cheaper 2nd gen stuff.

 

thats true but anything related to the Rotor itself is already accounted for i just needed help eliminating all the gaskets i didn't need from the OEM kit; so that i may buy them individually to save and invest the rest of the funds on others parts just as fuel system and such.

i'm already taking care of the water seals and rotor oil rings gaskets with Viton thanks to Bumstarts research

 

ok, hows this?

N3A1-13-111 Lower Intake Gasket
N3A1-13-112 Upper Intake Gasket

and whichever is the block to manifold gaskets.

 

if youre going single and all the INTERNAL parts are accounted for then the following list is all you need from the atkins kit that are EXTERNAL:

N3A1-13-111 Lower Intake Gasket
N3A1-13-112 Upper Intake Gasket
N3A1-15-116 W/P Housing Gasket
N386-15-162 Water Pump Gasket
N3YA-10-427 Oil Pan Gasket (optional. most use rtv with the banzai brace.)
N3A1-13-461 Exhaust Gasket
N3A2-14-293 Turbo Oil Drain (front oil return between engine and pipe)
N3A1-14-293 Turbo Drain Gasket (front oil return between turbo and pipe)
N390-14-602 OMP Crush Washer (only if keeping the OMP)
N3A1-10-424 Oil Fill Tube O-Ring
9956-20-800 OMP Crush Washer (only if keeping the OMP)
9956-21-000 Oil Injector Washer (only if keeping the OMP)
9956-21-400 Oil Line Crush Washers
9956-21-800 Oil Cooler Crush Washers
N350-14-604 OMP O-Ring (only if keeping the OMP)
NF01-13-ZG3 Lower Injector Grommet
NF01-13-ZG4 Upper Injector Grommet
9954-10-1601 Oil Filter Stand O-Rings
9954-10-1252 Diffuser O-Rings


then you will need a block off plate kit. if your kit comes with gaskets then use those. if it doesnt not then use the factory gasket for the part you are blocking off.

 

 

Thanks a lot Rex for coming through this with list and for the little side notes i will be making my own oil pan gasket with "the right stuff" and i'm also keeping the OMP.

as for the block off plates i found the really nice CNC cut EGR block off set with gaskets and hardware by blackpath for sale on ebay.

 

.

 

S4 steering racks available?

 

Any FTP pairs?

 

which part number are you looking for i still have a lot of gaskets left over

 

I have a feeling my phone pulled one on me lol... Pretty sure I replied to the wrong thread my bad.

 

Disregard (related thread scroll...)

 

Is the S5 dash available?

 

You replied to a for sale thread from 2012.

 

any mods care to post the original list?
that would be awesome.