OBD port...
#2
Eet fase
iTrader: (49)
Join Date: May 2002
Location: Lexington, SC USA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
There is a test connector in the engine that you ground and then turn to the key to ON. The light flashes the number of times to indicate what codes are stored in memory. I need to find the link to where that connector is...
EDIT: http://www.1300cc.com/howto/how2/codes.html
EDIT: http://www.1300cc.com/howto/how2/codes.html
Last edited by AcidShock; 07-22-05 at 12:45 AM.
#3
Full Member
Thread Starter
Join Date: Jun 2005
Location: Austin, TX
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Yeah... what i really need to find is where that is.
Whoops... same time for post
yeah, that's where i thought it was, pulled up a 12, looks like i need a new throttle sensor. would that cause my car to run like complete ****?
Whoops... same time for post
yeah, that's where i thought it was, pulled up a 12, looks like i need a new throttle sensor. would that cause my car to run like complete ****?
Last edited by Aruba27flr; 07-22-05 at 12:55 AM.
#4
Eet fase
iTrader: (49)
Join Date: May 2002
Location: Lexington, SC USA
Posts: 1,759
Likes: 0
Received 0 Likes
on
0 Posts
It could be a cause for hesitation, poor gasoline mileage, power issues. If it runs really, really bad I would be looking elsewhere though for broken, cracked vacuum hoses, dirty air filers and so on.
#5
Full Member
Thread Starter
Join Date: Jun 2005
Location: Austin, TX
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
ok... well after thinking about it, i realized that the previous owner probably had that code for a bit, washed away the oil in the rotor housings, and probably somewhere along there it lost compression in rotor 1... i just hope the rotor housings are in good shape.
#6
Lives on the Forum
Originally Posted by Aruba27flr
Where's the OBD port for the check engine light?
We don't need no stinkin' OBD crap!
NO RX-7 came with OBD or OBDII - Mazda dropped the production rather than require having that crap installed.
-Ted
Trending Topics
#8
Lives on the Forum
Originally Posted by beefhole
I thought we did get OBDI, but the thirg gen got canned because (among other things) wasn't OBDII compliant.
No, not even the FD has OBDI.
Mazda dropped U.S. production cause one of the reasons was all 1996+ vehicles in the U.S. were required to have OBDII.
-Ted
#10
Lives on the Forum
Yes, "OBD" is a (U.S.) standard.
Any OBD "scanner" can plug into an OBD port and scan the data.
Yes, the FC has some built-in error code save and display capabilities built into the stock ECU, but this has nothing to do with "OBD".
-Ted
Any OBD "scanner" can plug into an OBD port and scan the data.
Yes, the FC has some built-in error code save and display capabilities built into the stock ECU, but this has nothing to do with "OBD".
-Ted
Thread
Thread Starter
Forum
Replies
Last Post
Claudio RX-7
Haltech Forum
4
06-15-07 07:10 PM
GabrielJouChan
3rd Generation Specific (1993-2002)
2
04-22-07 03:43 AM