hkp

iTrader: (2)

well it finally got here, holset hx52, going on my 1990 turbo with a mild street port, 1600cc injectors in all 4 corners, e85 fuel, haltech e6k, hks cast manifold, 44mm wastegate, hks exhaust, not sure what size intercooler piping i want to use yet. hoping for some good numbers from this piece, cant go to big because the motor wasnt doweled when we rebuilt it. i will post pics when the car comes apart and then after tearbo has his way with it.

chatchie

iTrader: (22)

Is that T4 flanged? And if ya dont mind me askin, how much that run ya?

tearbo2

iTrader: (2)

this is gonna be fun !!!!

hkp

iTrader: (2)

you have to modify the bolt holes but it will work with a t4 flange, i got it for 500, the comp wheel is 67mm, the exhaust wheel is 70mm, and the housing is a 16cm^2.your damn right it is, the suspense is killing me.

nu-rx7junkie

iTrader: (1)

So you put this thing on yet? Mine is running now just tring to tune it and also getting another muffler the HBP is soo soo LOUD. I love it but neighbors dont. Im running 3" intercooler piping. Is your motor rebuilt? Did you stay with a S5 engine? How mush boost are going to be running?

hkp

iTrader: (2)

no s5 motor, i had already street ported and rebuilt a s4 so i just dropped it in, i wish mine was bridgeport, as far as boost goes, i will go as much as i can until i feel that the motor is going to take it. probably around 420 or so horse power.

20B10AE

iTrader: (14)

Nice turbo! I'll be getting an H1E with 22cm housing. I'll be using a Shook Motorsports manifold and DP so spool won't be too bad.

Good luck with your setup!

Reese

hkp

iTrader: (2)

thanks man, good luck on yours.

hkp

iTrader: (2)

its on and it sounds so awesome.

slpin

iTrader: (9)

looking good - how is the passenger side brake line?

hkp

iTrader: (2)

its fine

Turbodriven

Holset has their new HSS-Pro70. Its a T4 flanged unit with HSS-70mm wheel and 82mm turbine wheel. Sucker rocked on a 2JZ a local fellow built. Came on boost early and made some big numbers.

hkp

iTrader: (2)

where was it when i was shopping

Turbodriven

That is always the case. Holset now has their new HSS (Holset Super Series) line of units slowly releasing.

hkp

iTrader: (2)

jamespond24

iTrader: (13)

This is on 14.6psi?

hkp

iTrader: (2)

yep, a 1 bar spring

nu-rx7junkie

iTrader: (1)

Looking good what oil pressure are you running before turbo and what size restrictor into the turbo? How does it pull? I just drove mine for the first time today just got it where i can go around the street and start playing I still have lots of tuning to do. Looking good though.

hkp

iTrader: (2)

i just used the stock oil line, hacked it in the middle and had my friends at a hydraulic shop join the two pieces at the length i needed. no restrictor, just the stock oil line size.

siguy2k

iTrader: (3)

What was the torque? Also what did it put down peak hp and torque? Looks good! Is that on the stock manifold? Thanks

staticguitar313

iTrader: (2)

when are you seeing full boost by on this turbo?

hkp

iTrader: (2)

its laggy, im trying to find a way to get this thig spooled up faster. im seeing 14.6 psi around 5500 and i really want it a lot sooner.

Insomniac21772

thats a pretty decent sized turbo, how does the size compare to say a t04r or gt35?

hkp

iTrader: (2)

im not sure, ive never had either of those turbos.

Turblown

iTrader: (12)

That is really laggy for a 67mm wheel.

Are you sure you don't have any exhaust leaks before the turbo or any boost leaks?

Have you checked compression on the engine?