Savannah RX-7 Club
02-03-13, 03:56 PM
#3952
Full Member
Join Date: Nov 2009
Location: beaufort sc
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
got the rear subframes swapped out today so now my base is sitting with lsd, 5lug and fancy 4pot brakes lol. Now just gotta get the motor in wired up and drive....
02-08-13, 01:53 PM
#3958
Full Member
Its going in my 86 na .....I was hoping to get 300k out of the original engine but it fell just shy at about 280ish
Wanted to Bridgeport it but because Ed needs a car while his are getting finished and money is tight that's gonna have to wait....ill probably do that to the engine that is in the car currently
Figure. With the rtek ecu mod ad stock turbo injectors should be a fun little NA
Wanted to Bridgeport it but because Ed needs a car while his are getting finished and money is tight that's gonna have to wait....ill probably do that to the engine that is in the car currently
Figure. With the rtek ecu mod ad stock turbo injectors should be a fun little NA
Last edited by mfishe12; 02-08-13 at 02:13 PM.
02-12-13, 06:46 PM
#3961
Full Member
Reaching out again... does anyone have a good NA center iron? Ive got 3 bad ones ha ha ha. till get good with welding iron they are screwed.
thanks everyone! Especially Dana the rest of you're engine with be cleaned and ready if you need it!
thanks everyone! Especially Dana the rest of you're engine with be cleaned and ready if you need it!
02-16-13, 12:24 AM
#3963
Full Member
My rotary stuff over the week..went to ATLANTA for new Mazda 6 training and my instructor had a bunch of cool stuff including this 4rotor E- shaft from the 792- p car
Also went to Mazmart and got a tour of the facility and this sweet 4rotor
Also started cleaning up the stock ports on my NA build
Also went to Mazmart and got a tour of the facility and this sweet 4rotor
Also started cleaning up the stock ports on my NA build
02-16-13, 12:09 PM
#3965
Full Member
Join Date: Nov 2009
Location: beaufort sc
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
Parting out Rx7
dont wanna do it but i dont wanna blow more money fixing wrong ****, i get out of the military in 6 months and need to have some kinda money to live on......... Not leaving rotaries just gotta get better off before getting back into the 7 game.
dont wanna do it but i dont wanna blow more money fixing wrong ****, i get out of the military in 6 months and need to have some kinda money to live on......... Not leaving rotaries just gotta get better off before getting back into the 7 game.
02-20-13, 07:37 PM
#3967
Full Member
Parting out Rx7
dont wanna do it but i dont wanna blow more money fixing wrong ****, i get out of the military in 6 months and need to have some kinda money to live on......... Not leaving rotaries just gotta get better off before getting back into the 7 game.
dont wanna do it but i dont wanna blow more money fixing wrong ****, i get out of the military in 6 months and need to have some kinda money to live on......... Not leaving rotaries just gotta get better off before getting back into the 7 game.
02-21-13, 08:26 AM
#3969
Full Member
Join Date: Nov 2009
Location: beaufort sc
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
Was gonna part both out but might end up finishing the white one and hopefully be ok gettin out. Yes I have a good brake master. Anyone have exhaust gaskets. Need the 2 in the rear. Also can u run a usdm s4 t2 on a jspec n318 ecu and afm?
02-22-13, 03:40 PM
#3971
Full Member
iTrader: (26)
Join Date: Mar 2012
Location: Savannah, GA
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, it's been a little while since my last post but i've been away at school. I recently had a brand new single turbo wiring harness stolen from my doorstop in Savannah. Rywire sent it via USPS, and the postman confirmed that he left the package at my door. I never received the package. I reached out to all of my neighbors, but no luck. So if you see one being offered in the area, it could be the one that was stolen from me. Fortunately, Rywire is replacing the stolen harness. They are a great company.
02-22-13, 11:03 PM
#3972
Full Member
Hey guys, it's been a little while since my last post but i've been away at school. I recently had a brand new single turbo wiring harness stolen from my doorstop in Savannah. Rywire sent it via USPS, and the postman confirmed that he left the package at my door. I never received the package. I reached out to all of my neighbors, but no luck. So if you see one being offered in the area, it could be the one that was stolen from me. Fortunately, Rywire is replacing the stolen harness. They are a great company.
