TwinCharged RX7

iTrader: (14)

Picked up a used C west bumper (I think thats what brand it is haha), cut off the old wire mesh, put on new black plastic mesh (construction mesh). smoked 99 style lights from ebay. I could not get these with the harness, so I wittled away at the new housings and made the stock 94 turn signal bulb holder fit. I finished one, copied it on the other, and go figure, the bulb holders are slightly different on each side (one must have been replaced at some point). So out came the dremel to do some more cutting. Rather than trim the new housing more to fit the 94' driving light bulb holders, i found that the side turn signal bulb holders fit perfectly, so i spliced them in, the only downside is that the bulbs are a bit smaller and they look a little dim.

I also took the opportunity to put HID's in my hi beam so now i can actually see. I had put a larger projector from a Lexus in the EVO-R kit, and the H3 bulb wasn't bright enough to project through the lens. The new vendor on here came at just the right time and new ballasts and H3 HID bulbs only cost me 60 bucks. They are bright now, i can finally aim my HID low beams (stock from the EVO R kit) down now so they don't have to double as hi's and I can stop blinding people.

The fitment is decent, it already came painted black, but its easy to see that it was once red. Definitely could use a bit more work, but it is good enough for now until I put the panspeed flares on and paint the whole car next spring.

Before:




After:

purerx7

iTrader: (61)

Looks nice, however, that "construction" mesh looks really out of place. Just my .02.

TwinCharged RX7

iTrader: (14)

Yeah, its not quite what I wanted, but its way better than the wire mesh that was on it. When I get it painted I'll look into something a little better. I've seen the stuff on JC Whitney made for grills, I'll probably go with that in black, do you know of anything better than that?

SayNoToPistons

Not bad but the last picture was pretty much useless .

TwinCharged RX7

iTrader: (14)

Haha, yeah my battery died as soon as the picture was taken, so the flash didn't work very well.

TwinCharged RX7

iTrader: (14)

What do you think about not having a FMIC with this setup? I think the huge opening looks off without a big front mount. Think anyone would trade a front mount for the PFS race SMIC?

mark1rx7

stock > c-west sorry

Battle Cat

iTrader: (78)

+1,


i like the stock look better, cwest kills the body lines imo

staticguitar313

iTrader: (2)

+6

Ceylon

iTrader: (3)

Not bad, I think oem side lights & new mesh would make it look a lot better though
Cwest can look awesome if done right, and bad if done wrong.
Here is a example of a good c-west front, the colour helps it a lot I think.

Oun

iTrader: (3)

the C west bumper looks good. its just ugly when ppl get an aftermarket front bumper and thats it.

TwinCharged RX7

iTrader: (14)

I don't really like the C West sides, I'm trying to figure out what sides to go with.

R3AL.CH1CK3N

iTrader: (9)

looks good man. keep up the good work.

RE-Amemiya

Looks good!

Don't agree with the people that say the stock bumper is better than the C-West front. The '99 spec certainly is though.

killerrx710

iTrader: (8)

Seen the car in person looks real good

1QWIK7

iTrader: (33)

Hmm looks nice although not a fan of the CWEST.

I woulda went with the GTC front if i didnt go 99 spec.

TwinCharged RX7

iTrader: (14)

Thanks for the comments. I liked it at first, but its grown on me more everyday. Still haven't decided on the sides yet. I kind of like the ones that have a small circular duct down low near the back, can't remember the brand though. I'll look for a pic and post it up.

p.s. i just bought an 03 G35 coupe today, black to match, for $6k, haha, crazy deal for a daily driver

TwinCharged RX7

iTrader: (14)

This is one of banzai's cars, I think they are old apexi skirts. If I can even find these, what do you guys think of them with my front? They would probably blend in with the car a little better on mine because its black.