New 13B "street" rwhp king has gone to Marko from ForceFed
13BT on gas. Stock 13BT intake and TB



874 rwhp


Woot for the Little 13BT's that could

 

It doesn't even sound like it makes 800+ on the youtube video, compared to some cars we've dynoed making those types of hp, but congrats to them w/ making it with vp.

 

Waz Up fellas , post up the Vid .
Tiralo al medio Kabooski .

 

http://ca.youtube.com/watch?v=UQrPNvFx8eY here goes one of them i found.

 

Hi guys here is a engine shot. I think this was one of the 850hpo runs. The car has one 874 run, six 840-860 runs. This is all done on 25%vpimportand 75 q16.
http://ca.youtube.com/watch?v=8BeG-6mdRjM

Marko Stilinovic

 

You cant go by sound as you have no information about the rear diff ratio. And how high we were reving the car. Dont forget that this is a t4 small rear wheel s400 turbo. If I cut the run off at hp peak then it would definately sound right. But this car made full power by 8000 rpm. And then tapered in the 9500 mark. I was just seeing what this turbo did with the fuel supply at high rpms. Also we were seeing how the stock intake manifold and Tb would flow. I

Marko Stilinovic

 

CONGRATS !!!!!! don't make me go back to the dyno !!!!!



numbers are great on a dyno, but "we" all know where the number really counts. not taking anything away from you guys, good job.

is the engine ported or "stock"

 

Hb

 

Hey congrats those are some really good #'s to see out of a TII motor , what kind of porting you guys done to the engine ? I am currently having my engine built it's a S5 it going to be semi-pp with alot of mods shooting for 35psi+ it will be geting put together next week .

 

Look who's talking!!

Or **** my bad!















































I thought you were Ernie!!!

 

He did he's pulls in 4rth gear

Here is mine from a engine bay view like his
http://www.youtube.com/watch?v=nyA1Lp77Qgo
I did mine on 3rd gear and Have a similar setup. Except the fuel pump was a POS
and could not let me run more boost pass 26PSI with AFR's in the mid 10's to keep the engine from blowing up.......I did upward mid 500's

4x1600cc
S475 1.15 T6 vs S480 1.10 T4
13B-REW HB VS 13BT HB

I may soon switch to a 4bar MicroTech after I finish doing my overkill fuel/ignition setup and see what I can do at 40+ PSI

Very inspiring Marko
Just when you think we're getting left behind by evo/hondas etc
you prove 13B can still do it! I love it!!!!!!!!!!!!!!!!!!!!!!!!!!!!

 

Left behind where? On the dyno or at the track!

 

Agreed. Mph is the only dyno that dictates hp.

But unfortunatley there is snow on the ground and the track is closed untill march.

The car will run with this set up. This engine has lasted 60 000kms. We will see how much of it will make it to the pavement?

The engine is a half bridge originaly taught to me by Jon Blanch of RX engineering and Microtech EFI. Jon has helped me along with my tuning and to give me the confidence in turning up the boost. LOL Everything else was time on the dyno.
You need the practice to build confidence.

Marko Stilinovic

 

So how much power does it take to do 150mph in a 2700lb street rx7?

 

We'll see soon enough my friend we shall see soon enough
The only reason why we run like **** is cause they have better aftermarket tranmission support then we do for there OEm transmissions....


Face'd Liberty T56 should make things a bit more fair

 

I know of one stock ported motor rx7 that does 140mph with 550whp.

 

On the dyno, and if all drivetrain equipment is similar??? Then on the track!
\

 

Who's we?

So it's the transmission at fault then?
I thought it was some of them horses getting left behind on the dyno!

 

Depends on ratio and tire size. But in general you shoud have a good 700 to make 150. I did 147 with 700 on a 4.1 rear diff.

Marko Stilinovc

 

Congrats on the numbers!











And not funny Cris!!!

 

BTW.
Congrats on the power. Car sounds sweet. Track opens here at the end of the week.

 

I hit 149mph, but weigh 2880lbs.

 

Yes I blame the non High RPM shifting POS oem tranmissons! lol
A good tranny is key to using those horses

 

Ernie!

I'm suffering from Methanol poisoning

 

I hit 150 at 2620lbs with 640whp!