Fitting the 99 Spec Bumper to 93
#1
Junior Member
Thread Starter
Join Date: Dec 2018
Location: UK based, Car in Portugal
Posts: 22
Received 0 Likes
on
0 Posts
Fitting the 99 Spec Bumper to 93
Sorry guys, tried to search but nearly the whole forum came on results. Nothing straight forward on FAQ topic.
How is the fitment of a 99 Spec bumper into a 93 model with two oil radiators, should it be straight/nearly forward on counting with some possible chassis torsion?
Is there any difference between LHD and RHD?
Looking to buy the below.
https://i.ebayimg.com/images/g/AVYAA...xE/s-l1600.jpg
https://i.ebayimg.com/images/g/hJAAA...tU/s-l1600.jpg
https://i.ebayimg.com/images/g/19IAA...tT/s-l1600.jpg
https://i.ebayimg.com/images/g/RP4AA...tR/s-l1600.jpg
How is the fitment of a 99 Spec bumper into a 93 model with two oil radiators, should it be straight/nearly forward on counting with some possible chassis torsion?
Is there any difference between LHD and RHD?
Looking to buy the below.
https://i.ebayimg.com/images/g/AVYAA...xE/s-l1600.jpg
https://i.ebayimg.com/images/g/hJAAA...tU/s-l1600.jpg
https://i.ebayimg.com/images/g/19IAA...tT/s-l1600.jpg
https://i.ebayimg.com/images/g/RP4AA...tR/s-l1600.jpg
The following users liked this post:
SevenSin (08-21-19)
#3
Urban Combat Vet
iTrader: (16)
(Searched in title only using term “bumper” in 3rd Gen. tech section):
In addition to maintaining safety, to make it look decent and to function properly you need the parts listed in post #6 plus the styrofoam filler/backing which I didn’t see mentioned but pretty sure it’s specific to the bumper...
—-> https://www.rx7club.com/3rd-gen-gene...umper-1131905/
In addition to maintaining safety, to make it look decent and to function properly you need the parts listed in post #6 plus the styrofoam filler/backing which I didn’t see mentioned but pretty sure it’s specific to the bumper...
—-> https://www.rx7club.com/3rd-gen-gene...umper-1131905/
Last edited by Sgtblue; 08-19-19 at 09:50 AM.
The following users liked this post:
SevenSin (08-21-19)
#4
Junior Member
Thread Starter
Join Date: Dec 2018
Location: UK based, Car in Portugal
Posts: 22
Received 0 Likes
on
0 Posts
Thank you for the reply. I have been looking into it and the reinforcement structure is either rare to find around Europe or extremely expensive (more than the whole front end with lights and lip included). So I might need to go with reinforcement structure cutting, although I have seen some people on youtube fit a 99 Spec bumper without mentioning or showing any cutting?
The whole parts list would add quite a lot of money. Would just the bumper, lip and lights be such a bad thing to have?
Regards
The whole parts list would add quite a lot of money. Would just the bumper, lip and lights be such a bad thing to have?
Regards
Last edited by SevenSin; 08-21-19 at 02:02 AM.
The following users liked this post:
SevenSin (08-21-19)
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Dec 2018
Location: UK based, Car in Portugal
Posts: 22
Received 0 Likes
on
0 Posts
Would this be worth to buy or am I better just cutting the one I have installed, which I think it is the foam one? To what I can understand I will only need to open a bit more where the turn signals fit in. Might lose some stability at the bottom which I will try to sort out as I have an under tray on the stock.
https://www.ebay.co.uk/itm/MAZDA-RX7...sAAOSwaRRcjRkH
https://www.ebay.co.uk/itm/MAZDA-RX7...sAAOSwaRRcjRkH
Thread
Thread Starter
Forum
Replies
Last Post
str8ryd
3rd Generation Specific (1993-2002)
5
09-18-06 06:04 PM