Microtech Area is for discussing Microtech systems

Microtech went back to the dyno

Old 12-14-03, 07:09 PM
  #1  
Rotary Enthusiast
Thread Starter
 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,307
Likes: 0
Received 0 Likes on 0 Posts
went back to the dyno

Had a dyno day on yesterday, things were a little slow so i threw my car on there,

first pull on 10psi was 350rwhp, then wound it up to 12psi went 380rwhp, then put 14psi into it and after a few pulls to get the tune better went 405.6rwhp on a dyno dynamics dyno, which is about 480 on the dyno jets (going on the 20% difference between the 2 dynos)

still need more time tuning and it will probably crak 415 on 14psi.,

Dale
10sec rx7 is offline  
Old 12-14-03, 09:35 PM
  #2  
New Project on the Way...
iTrader: (2)
 
jreynish's Avatar
 
Join Date: Apr 2002
Location: Yellowknife, NT
Posts: 3,760
Received 0 Likes on 0 Posts
Dale,
what kind of turbo, WG, intercooler and bov are you running? also are you still unsing stock intake and TB?
jreynish is offline  
Old 12-14-03, 10:03 PM
  #3  
Rotary Enthusiast
Thread Starter
 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,307
Likes: 0
Received 0 Likes on 0 Posts
the turbo is a hybrid T04 with a 1.32 P trim rear, .70 comp cover with a turbonetics T66 comp wheel in it,

WG is a garrett 42mm

intercooler is a 550x450x75mm custom unit. 2.5" pipe in and 3in pipe out.

stock 87 T2 inlet manafold, stock throttle body with the 2 extra butterflys removed

the BOV's are just australian made units, both venting to atmo,

ecu is a LTX12, injectors are 2x550 and 4x1200cc, fuel pumps are 1xcarter pre pump to fill surge tank, 2x bosch 910's, malpassi FPR,

Dale
10sec rx7 is offline  
Old 12-14-03, 10:28 PM
  #4  
New Project on the Way...
iTrader: (2)
 
jreynish's Avatar
 
Join Date: Apr 2002
Location: Yellowknife, NT
Posts: 3,760
Received 0 Likes on 0 Posts
that is impressive dale! Good numbers!
jreynish is offline  
Old 12-15-03, 05:30 PM
  #5  
Rotarded since 1992
15 Year Member
iTrader: (12)
 
legendrx7's Avatar
 
Join Date: Feb 2001
Location: Little Rock, AR, USA
Posts: 327
Likes: 0
Received 0 Likes on 0 Posts
~480whp @ 14psi! very nice numbers

Last edited by legendrx7; 12-15-03 at 05:34 PM.
legendrx7 is offline  
Old 12-15-03, 05:35 PM
  #6  
Rotary Enthusiast
Thread Starter
 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,307
Likes: 0
Received 0 Likes on 0 Posts
10sec rx7 is offline  
Old 12-15-03, 05:48 PM
  #7  
New Project on the Way...
iTrader: (2)
 
jreynish's Avatar
 
Join Date: Apr 2002
Location: Yellowknife, NT
Posts: 3,760
Received 0 Likes on 0 Posts
Dale,
do you have any pictures of your setup, I am currious as to how you have it setup? If you wish to keep a secret I respect that as well.
Also is your custom intercooler normally piped or is it a v-type?
jreynish is offline  
Old 12-15-03, 06:07 PM
  #8  
Rotary Enthusiast
Thread Starter
 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,307
Likes: 0
Received 0 Likes on 0 Posts
here is a pic of the engine bay,

it is pretty old tho!

Dale
10sec rx7 is offline  
Old 12-15-03, 06:31 PM
  #9  
New Project on the Way...
iTrader: (2)
 
jreynish's Avatar
 
Join Date: Apr 2002
Location: Yellowknife, NT
Posts: 3,760
Received 0 Likes on 0 Posts
WOW very clean! Impressive, what type of core is that for the intercooler?
jreynish is offline  
Old 12-15-03, 06:40 PM
  #10  
Rotary Enthusiast
Thread Starter
 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,307
Likes: 0
Received 0 Likes on 0 Posts
thats not clean!! ill get some new pics of it!!

i wouldnt have a clue what type of core it is, some type of tube and fin!

Dale
10sec rx7 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Th0m4s
Build Threads
25
02-26-19 02:04 AM
C. Ludwig
Single Turbo RX-7's
49
01-30-19 06:31 AM
Queppa
New Member RX-7 Technical
8
09-02-18 09:53 AM
Turblown
Single Turbo RX-7's
0
08-14-15 04:48 PM
Clacor
Single Turbo RX-7's
0
08-14-15 09:17 AM


Thread Tools
Search this Thread
Quick Reply: Microtech went back to the dyno


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: