Microtech Area is for discussing Microtech systems

Microtech dumb microtech question

Old 08-18-07, 03:23 PM
  #1  
Senior Member

Thread Starter
 
Join Date: Sep 2003
Location: Berthier, Quebec
Posts: 355
Likes: 0
Received 0 Likes on 0 Posts
dumb microtech question

Hi there!

I'm not having quite a lot of trouble with my T2!

car n mods :

87T2, reman motor with 45 000KM, 100 PSI on each rotor, hybrid turbo with monster ported WG, HKS front mount, 550/1500CC injectors, Old school greddy BOV, emission removed, TB mod, greddy profec B spec 2 at 7/11 psi etc

Long story short:

Got a broken microtech while the guy told me it was in working condition ( thanks Smoken' ) and it turns out it was only a blown transistor and 2 circuit's traces blown on the cardbord. My friend's cybernetic shop took care of that rapidly.

Then I got my car street tuned du Steve Kan (as you may know, he comes down to quebec every summer) and during a whole summer it drove great. Steve told me my engine was healthy and tuned me to 7 and 11 psi (really moderate as you can see, I like to be on the safe side )

But my idle speed was too high (around 1100 rpm) since I'm on stock ports. So I tried to fix this, but I got mistaken between the throttle stop screw and the TPS screw(dumbass). Ever since that moment, the car acted funny, with bizzare AFr.

So I called one buddy with his laptop and fixed the TPS issue. it's now properly calibrated.

Since the engine had flooding trouble, I sent all my injectors at Rc engineering and they are all now perfect. My AFr are more adequate too

Now here's the problem : If i charge the battery for the day and start the car after a day or two, it starts almost right up! but it doesnt hold his idle. If it descends at 1000 rpm, it wants to die. if it dies, I cant get it to start immediatly after. If I wait till the day after, it starts right up but still doesnt hold his idle!

what could cause that???

could a vacuum leak cause my problems??

the wiring is correctly done since I made it with father and he is an electrician.

Any input would be appreciated, since I never drove my rx-7 this summer and I did drive it all the time previous summer.

thanks a lot

l-p
Old 08-18-07, 04:28 PM
  #2  
mmm doritos

iTrader: (4)
 
13bturbofc's Avatar
 
Join Date: Apr 2006
Location: lancaster PA
Posts: 2,107
Likes: 0
Received 0 Likes on 0 Posts
did you test your alternator?
Old 08-18-07, 04:37 PM
  #3  
Senior Member

Thread Starter
 
Join Date: Sep 2003
Location: Berthier, Quebec
Posts: 355
Likes: 0
Received 0 Likes on 0 Posts
how would this be related to a starting issue??
Old 08-18-07, 07:44 PM
  #4  
mmm doritos

iTrader: (4)
 
13bturbofc's Avatar
 
Join Date: Apr 2006
Location: lancaster PA
Posts: 2,107
Likes: 0
Received 0 Likes on 0 Posts
you said you had to keep changing your battery and the car wont start if the alternator and or battery isnt right
Old 08-19-07, 09:55 AM
  #5  
Engine, Not Motor

iTrader: (1)
 
Aaron Cake's Avatar
 
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes on 91 Posts
Map is probably too lean to sustain a cold start. Try tuning up both the Af_StE a few percent and increase the Water map a few percent.
Old 08-22-07, 12:44 PM
  #6  
Senior Member

Thread Starter
 
Join Date: Sep 2003
Location: Berthier, Quebec
Posts: 355
Likes: 0
Received 0 Likes on 0 Posts
Well aaron if it dies, doesnt that mean its too RICH instead on lean?

because when i get it started and keep the throttle to 2000-3000 rpm ( in neutral of course) I get air/fuel around 13.5 and sometimes it goes down to 13

what do you think?
Old 08-23-07, 10:03 AM
  #7  
Engine, Not Motor

iTrader: (1)
 
Aaron Cake's Avatar
 
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes on 91 Posts
The engine will idle quite well at 13:1. But if you start it and it immediately dies, then it needs more fuel.

What is the exact problem here?
Old 08-23-07, 11:36 AM
  #8  
Senior Member

Thread Starter
 
Join Date: Sep 2003
Location: Berthier, Quebec
Posts: 355
Likes: 0
Received 0 Likes on 0 Posts
If I let the car sit for a day and have a full battery, it starts almost right up. (although sometime I have to play a little with my fuel pump cut switch, but the car has always done that... )

But once it's started, i have to hold the throttle to keep the engine running. As soon has I take my foot off the gas pedal, when the rpm goes down to 1000, the engine starts to tumble, shake and shuts off

With my foot on the gas pedal holding it to 2000-3000 rpm, I see air fuel ratios from 12 to 14

When it dies because I took my foot off the gas pedal, it doesnt want to start immediatly after. I have to let it sit for a couple hours. It sounds like flooded I know, but remember I got my injectors Back from RC engineering and they are now all excellent and non dripping

So I'm pretty confused on this one!!!

You think adding more fuel will help it???
Old 08-23-07, 06:37 PM
  #9  
Rotary Freak

iTrader: (8)
 
rx72c's Avatar
 
Join Date: Jun 2003
Location: Australia
Posts: 2,795
Received 111 Likes on 62 Posts
Add more fuel to the idle map. 13:1 is too lean.
Old 08-24-07, 10:05 AM
  #10  
Engine, Not Motor

iTrader: (1)
 
Aaron Cake's Avatar
 
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes on 91 Posts
12:1 is way too rich when holding the throttle under no load at 2000 RPM, 14:1 is probably too lean to give you a decent idle until the car is fully warmed up.

Last edited by Aaron Cake; 08-24-07 at 10:05 AM. Reason: Edit...I mean lean, dammit....
Old 08-30-07, 02:44 AM
  #11  
Rotary Freak

iTrader: (8)
 
rx72c's Avatar
 
Join Date: Jun 2003
Location: Australia
Posts: 2,795
Received 111 Likes on 62 Posts
get your idle to 12.5:1 on idle. and it will be right.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
_Tones_
Adaptronic Engine Mgmt - AUS
10
05-25-21 05:37 AM
freq
Haltech Forum
5
09-13-15 07:45 AM
DerpyToast
2nd Generation Specific (1986-1992)
13
09-07-15 12:20 AM


Thread Tools
Search this Thread
Quick Reply: Microtech dumb microtech question



All times are GMT -5. The time now is 08:40 AM.