Haltech Post Haltech Base Map REQUESTS Here
#331
No Pistons
iTrader: (10)
I need a base map for a S4, 550/550 injectors, stock turbo, pretty much all stock with a 2 bar map sensor ( I can change that once I get a baseline map) for an E6K.
Thanks guys I need to get my car to start .
Email is Rnz520@yahoo.com
Renzo
Thanks guys I need to get my car to start .
Email is Rnz520@yahoo.com
Renzo
#333
Junior Member
Join Date: Oct 2009
Location: Greenwood, IN
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Can you help me with an E8 base map for initial set up?
My specs are:
S4 TII 13BT - Street ported
660 Hi Impedance/ 1600 Low Inpedance Primary & Secondary Injectors
Stock Coils, and all sensors except for 3 Bar Map
T72 / 81P Exhaust - Turbo
Custom Turbo Manifold
3" Downpipe
Front Mount Intercooler - 2.5" Out / 3" in to Throttle
External Bosh 044 Fuel Pump
-8AN Braided Fuel Line IN
-6AN Fuel Return
HKS light Flywheel and counter balance
Fuel Lab Pressure Regulator
Turbo Smart - Manual Boost Controller
Haltech E8
No PWM / Aux Outputs enabled
Warm and humid weather all year around => Puerto Rico
Expected HP 400+++++
My email address is vmerinorx7@gmail.com
Thanks in advance.................
My specs are:
S4 TII 13BT - Street ported
660 Hi Impedance/ 1600 Low Inpedance Primary & Secondary Injectors
Stock Coils, and all sensors except for 3 Bar Map
T72 / 81P Exhaust - Turbo
Custom Turbo Manifold
3" Downpipe
Front Mount Intercooler - 2.5" Out / 3" in to Throttle
External Bosh 044 Fuel Pump
-8AN Braided Fuel Line IN
-6AN Fuel Return
HKS light Flywheel and counter balance
Fuel Lab Pressure Regulator
Turbo Smart - Manual Boost Controller
Haltech E8
No PWM / Aux Outputs enabled
Warm and humid weather all year around => Puerto Rico
Expected HP 400+++++
My email address is vmerinorx7@gmail.com
Thanks in advance.................
#335
Junior Member
Hello anyone! This forum very useful! THX for everyone!
I try to tune stock PS1K S5 map for my specs. But not so will turn out =)
May anybody help me with base maps for my specs:
Stock Ignition and CAS wired by diagram finden on this forum.
Primay 750
Secondary 1600
StreetPort Pineapple
Removed all BAC, EGR, ACV, cold start from Throttle and other
IDLE is 1000rpm tuned by screw on throttle body =)
installed TPS
Fuel pressure without vacuum (MAP) 41psi
onboard map sensor
Garrett GT3582R
V-mount intercooler 2,5 in/out
Exhaust all the way 3" from turbo
my mail is xslalom@yandex.ru
Please PM me for any additional questions about my specs
PS Have anyone Calibration to stock IAT S4/S5 sensor?
Many Thanks!
I try to tune stock PS1K S5 map for my specs. But not so will turn out =)
May anybody help me with base maps for my specs:
Stock Ignition and CAS wired by diagram finden on this forum.
Primay 750
Secondary 1600
StreetPort Pineapple
Removed all BAC, EGR, ACV, cold start from Throttle and other
IDLE is 1000rpm tuned by screw on throttle body =)
installed TPS
Fuel pressure without vacuum (MAP) 41psi
onboard map sensor
Garrett GT3582R
V-mount intercooler 2,5 in/out
Exhaust all the way 3" from turbo
my mail is xslalom@yandex.ru
Please PM me for any additional questions about my specs
PS Have anyone Calibration to stock IAT S4/S5 sensor?
Many Thanks!
#336
Junior Member
Join Date: Nov 2008
Location: rotorland
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
Could someone please shed some light on the transient throttle settings? I have a s5 13bt large street port, 1200cc/2200cc, ps1000
When the car warms up it is fine
Though when I touch the throttle cold it stalls or comes very close to stalling, is this just because of the cold operation transient throttle settings? I've tried playing with them but haven't had alot of luck yet
Thanks in advance
When the car warms up it is fine
Though when I touch the throttle cold it stalls or comes very close to stalling, is this just because of the cold operation transient throttle settings? I've tried playing with them but haven't had alot of luck yet
Thanks in advance
#337
Junior Member
Join Date: Feb 2010
Location: Greece Chios
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Hi...
I really need a base map in order to get a ride with my FD...
So I beg for a little help...!!!!!!
The main problem of my car is the fuel consumption including the price of the gasoline here in Greece (2$ per litre 95ron) that's why I really could use a little help here in order to be able to go for a ride without spending a fortune for fuel...
Here is my setup:
1. 1992 FD3S
2. 13B-RE short block only big porting, with FD's induction manifold, twin turbos etc... All the peripherals on the RE short block is from the FD...!!! So I guess that the engine is working as an 13B-REW...!
3. OEM 92 model Twin turbos NON sequential
4. Haltech P1000 EMS
5. Sard 280 fuel pump
6. 850cc primary injectors and 1680cc secondary injectors (high impedance) bought from RX7-store.net (not advertising) on brand new aftermarket fuel rails
7. Fuel Pressure Regulator @ 45psi
8. Greddy FMIC
9. 90mm exhaust from downpipe to the end no cat handmade, just midpipe and the final one...
10. Greddy intake mushrooms
11. LS1 coils (4 of them) direct fire
12. APEXI AVCR Boost controler but never setup-ed...
13. OEM spark plugs and OEM wires
14. Use the map sensor built in the P1000
As I said my main problem is the fuel cunsumption... At this time the engine is running pretty rich (tune the idle speed from the throttle cable) and I really don't know the overboost... But I saw 7,5psi on the boost gauge @ 2000rpm....
The rev limiter is at 5000rpm and I'd prefer not to be increased right now for safety reasons...
I'd like a basic map just to run the engine smoother and lower the fuel consumption, in order to be able to collect about 1500$, travel by ship to Athens (I live on an island here in Greece) and get a final tune...
Please help me..!
I really need a base map in order to get a ride with my FD...
So I beg for a little help...!!!!!!
The main problem of my car is the fuel consumption including the price of the gasoline here in Greece (2$ per litre 95ron) that's why I really could use a little help here in order to be able to go for a ride without spending a fortune for fuel...
Here is my setup:
1. 1992 FD3S
2. 13B-RE short block only big porting, with FD's induction manifold, twin turbos etc... All the peripherals on the RE short block is from the FD...!!! So I guess that the engine is working as an 13B-REW...!
3. OEM 92 model Twin turbos NON sequential
4. Haltech P1000 EMS
5. Sard 280 fuel pump
6. 850cc primary injectors and 1680cc secondary injectors (high impedance) bought from RX7-store.net (not advertising) on brand new aftermarket fuel rails
7. Fuel Pressure Regulator @ 45psi
8. Greddy FMIC
9. 90mm exhaust from downpipe to the end no cat handmade, just midpipe and the final one...
10. Greddy intake mushrooms
11. LS1 coils (4 of them) direct fire
12. APEXI AVCR Boost controler but never setup-ed...
13. OEM spark plugs and OEM wires
14. Use the map sensor built in the P1000
As I said my main problem is the fuel cunsumption... At this time the engine is running pretty rich (tune the idle speed from the throttle cable) and I really don't know the overboost... But I saw 7,5psi on the boost gauge @ 2000rpm....
The rev limiter is at 5000rpm and I'd prefer not to be increased right now for safety reasons...
I'd like a basic map just to run the engine smoother and lower the fuel consumption, in order to be able to collect about 1500$, travel by ship to Athens (I live on an island here in Greece) and get a final tune...
Please help me..!
#338
BDC Motorsports
#341
Senior Member
iTrader: (3)
Hey Gang,
New PS1k.................gt35r large port, open exhaust. Anyone, anyone? Beuller? Beuller?
please email to Master.eagle@horizonlines.com as I am at sea. Thanks gents.
3" exhaust, large IC, 3 bar map, full race, Fuel pump separate, fan separate,
550/1680
New PS1k.................gt35r large port, open exhaust. Anyone, anyone? Beuller? Beuller?
please email to Master.eagle@horizonlines.com as I am at sea. Thanks gents.
3" exhaust, large IC, 3 bar map, full race, Fuel pump separate, fan separate,
550/1680
#343
Full Member
iTrader: (1)
Join Date: Feb 2009
Location: UK
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
Hey all,
Im in need of a map below are the specs of my setup
PS1000
12a large extend port
TO4r or T67
4x 1000cc Rochester injectors
Bosch 044 pump
3” exhaust
bo0557 (@) gmail.com
thanks guys..
Im in need of a map below are the specs of my setup
PS1000
12a large extend port
TO4r or T67
4x 1000cc Rochester injectors
Bosch 044 pump
3” exhaust
bo0557 (@) gmail.com
thanks guys..
#344
Senior Member
iTrader: (7)
Join Date: Jul 2008
Location: ohio
Posts: 253
Likes: 0
Received 0 Likes
on
0 Posts
E8 haltech map
I have a e8 mods are 89 s5 rx7 with a turbo II with a knights sports turbo, front mount intercooler , 750 high impedance injectors primary, 1200 low impedance injectors for secondary, stock ignition, Gm 3bar map, 5 speed car, 3" exhaust, using factory engine harness with a haltech plug and play, all I need is a base map to these settings for me to tune from, I want to be able to tune my car my self. Let me know if you need any more info. If you can help me get a map with these settings that would be awesome this is all I need and I can get my car going for the summer.
#345
Creeper
iTrader: (3)
Join Date: Oct 2008
Location: Corpus Christi
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Hey BDC, can u please make me a base map i can work from.
Haltech PS1000 /using On Board map sensor.
Knightsports rf320
720cc's prim & 750cc's sec
stock ignition
stock pump
stock IC
3" exhaust no cats
Would greatly appreciate it
Haltech PS1000 /using On Board map sensor.
Knightsports rf320
720cc's prim & 750cc's sec
stock ignition
stock pump
stock IC
3" exhaust no cats
Would greatly appreciate it
#346
talking head
I have a e8 mods are 89 s5 rx7 with a turbo II with a knights sports turbo, front mount intercooler , 750 high impedance injectors primary, 1200 low impedance injectors for secondary, stock ignition, Gm 3bar map, 5 speed car, 3" exhaust, using factory engine harness with a haltech plug and play, all I need is a base map to these settings for me to tune from, I want to be able to tune my car my self. Let me know if you need any more info. If you can help me get a map with these settings that would be awesome this is all I need and I can get my car going for the summer.
pretty sure i have it as both stock coil and for 4 x ls1 coils , for 3 bar map sensor
if no one bites with something more suitable,, PM me and you can have it as a baseline
its for 1.71 halwin ,, is 9000 rpm and 29 psi limited , and has 100 rpm defintions around the idle point 600- 1100 rpm
so is a pretty handy , well spaced along the axis map for a street car
Last edited by bumpstart; 03-17-11 at 01:02 AM.
#347
Hi guys,
I just got a new setup up and I was looking for a base map. I tried to click on some of the links, but they seem to be not working..
I have a S5 13BT
Haltech E6X
Stock coils
Stock TPS
Stock CAS
3 BAR external MAP sensor
High imp 650cc primary injectors
Low imp 1680cc secondary injectors
60-1 turbocharger
large intercooler
Thanks for any help you guys can give me.
I just got a new setup up and I was looking for a base map. I tried to click on some of the links, but they seem to be not working..
I have a S5 13BT
Haltech E6X
Stock coils
Stock TPS
Stock CAS
3 BAR external MAP sensor
High imp 650cc primary injectors
Low imp 1680cc secondary injectors
60-1 turbocharger
large intercooler
Thanks for any help you guys can give me.
#348
Junior Member
Hi guys,
I just got a new setup up and I was looking for a base map. I tried to click on some of the links, but they seem to be not working..
I have a S5 13BT
Haltech E6X
Stock coils
Stock TPS
Stock CAS
3 BAR external MAP sensor
High imp 650cc primary injectors
Low imp 1680cc secondary injectors
60-1 turbocharger
large intercooler
Thanks for any help you guys can give me.
I just got a new setup up and I was looking for a base map. I tried to click on some of the links, but they seem to be not working..
I have a S5 13BT
Haltech E6X
Stock coils
Stock TPS
Stock CAS
3 BAR external MAP sensor
High imp 650cc primary injectors
Low imp 1680cc secondary injectors
60-1 turbocharger
large intercooler
Thanks for any help you guys can give me.
#349
Could you please shine a bit more light on the subject..? what kind of resistors? Just solder them inline with the positive wire going to the injectors? do you know where i can get these injectors?
Thanks for the heads up.
Thanks for the heads up.