BDC

Shoot me an email with more indepth specs as well as the system it's running on. bdc@bdcmotorsports.com

B

teamdod

never got a reply from u.....

BDC

You sure? Re-send your email to me.

B

fastrx7man

iTrader: (63)

did you get my email? It was from bmobley@adt.com.

thanks,

bill

PISTONSLAYER

Changed my combo since it was way too different. Hopefully now someone has a base map close enough to get this thing started pleeeeaaassseee; someone throw me a rope.

Combination:

- 12A Peripheral Ported N/A
- (4) 750 injectors
- 86 CAS with 86 Coils
- E6K


Any help greatly appreciated guys.

BDC

Send me an email with that and I'll make something for you today. bdc@bdcmotorsports.com

Pettersen

iTrader: (1)

I'm going to buy a Haltech P1000, so i need a basemap

88 T2
Streetport
720cc secondary injectors, stock T2 primaries.
32mm wastegate
T70 turbo
ebay manifold
90mm downpipe wich splits in to two 2,5", no cat.
emission system removed
Fmic(not yet but will get mounted before the Haltech)
Walbro fuel pump
Runs on 91octane any use mapping it to run on 93octane?

BDC

^^^ Read my posts. Shoot me an email with all of the specs.

B

Sideways7

iTrader: (7)

I need a base map for an E6X. Stock s4 motor, stock turbo, stock coils, 550 primaries, 1680 secondaries, 3 bar MAP sensor, haltech wideband.

Thanks!

bewst12psi

iTrader: (7)

Hey Brian,


I need a base map for a Platinum 1000.

Stock port s4 TII
1000cc primary / 1000cc secondary
Stock coolant sensor
GM/Haltech IAT
80mm TB w/ Ford TPS
Stock Coils
Using the internal 2bar MAP sensor
Precistion 6262 turbo

BDC

Email me this, bewst12psi. I'll get one made for you.

B

bewst12psi

iTrader: (7)

you're the man.

Email sent.

dznutzuk

iTrader: (1)

Hey Claudio-BDC I desperately need a map for my setup:

13BRE turbo motor
medium streetport(used pineapple cutouts)
Haltech e6k
3 bar map
ls1 coils
KKK K27/28 (roughly the size of a gt3540 a little bigger)
polished FD throttlebody
Bosch 044 255 fuel pump
1680cc secondarys
550 primarys
fmic
3 inch exhaust
13BRE CAS (2seperate grounds) with direct fire not toggle

One problem I have encountered is that when I'm trying to zero my timing with an old map that I had from my FD single, is that I lock the timing to -5 and zero it(although it's going a little back and forth-not steady dead on) and when I unlock it I lose it. Is this normal? At first I thought maybe I had the cas inserted wrong so I took it out and turned the engine 180degrees and it wasn't lining up properly so I did it again and still wasn't lining up correctly. I then switched the trailng spark wires and that did the trick-although I don't understand why. Claudio-BDC, I've been trying to set it up using Hitman's instructions but not with distributor mode that he states because trailing 2 is not firing. Also I'm using the 11tooth setup. What should I do about this? I can feel the engine trembling. Thank you so very much guys!!!

Claudio RX-7

iTrader: (1)

BASE MAP Thread updated with working links and some new Platinum maps too.

https://www.rx7club.com/forum/showthread.php?t=761825

2slow4stock

iTrader: (18)

Hey Brain, I need a map or can I run the 550/800, with t04e and fmic for the set up I have.

I am running fb 680cc primary, and 1000cc secondary.
I have a t3/t4 .60 trim hybrid, fmic.
Street ported motor n/a motor with TII intake manifolds with s4 n/a interals.
3 bar map sensor, msd a6 on leading coils, 3" turbo back exhaust.
Running stock coolant temp sensor, 14psi on the aftermarket wastegate. (Can't turn down)

R1_stormrider

requesting a v1.03 base map for a haltech platinum sport 1000. due to my password situation i need one just so i can overwrite the encrypted map that is currently on my ECU.

it doesnt matter whats on it since im going to erase it and use a brand new base map i have been given. i just need this so i can have a chance to upgrade my firmware.

the v1.03 base map will NOT be used to start my car, only as a way to clear my ECU. thank you! i am asking this because i have misplaced my factory CD last year...

Javier

Ok need a base map for a 20b on a new haltech Platinum 2000. mainly the fireing order and ignition setup with stock coils.

LUV94RX7

iTrader: (3)

Need base map to get started on a PS1000.

Steve Kan Stage III street port, T67 Turbo, Aquamist HFS-3 50/50 meth/water, 3" perf exhaust, E85, Profec B(20&30psi), 4-2200cc injectors, TwinPower, stock coils

Thanx,
Ken

BDC

Hi Ken,

3rd gen I take it? A base map for that (at least the fuel end) will be a real pain in the rear end.

B

LUV94RX7

iTrader: (3)

I currently have a Power FC, Datalogit and it was tuned by Kan for E85, I'm upgrading to Haltech 1000 and HFS-3.

Ken

Dzire

iTrader: (1)

I am getting platinum 1000 and I'm going to need a map
88TII
s4 Stockport motor
75 pound injectors primary and secondary
stock coils
Fmic
s5 TPS
stage 2 BNR turbo on 10 pounds of boost
runs on 93 octane
internal map sensor

RXTASY57

iTrader: (2)

Looking for a E6K base map for E85.
3 bar map sensor-4XID2000cc injectors.
These injectors rock BTW! HBP idles at 1600 RPM and 14:1 AFR!

genji

iTrader: (3)

Hi, I am finishing up some major work on my car and I am going to need a base map soon. I have an s5 turbo II with:

13b engine
Haltech platinum sport 1000 (using on board 2.5 bar map)
bnr stge II turbo
fmic 3" in and out
denso 720 cc injectors
walbro 255 fuel pump
stock coils and fuel pressure regulator
stock cas
3" turbo back exhaust
rotary performance dual belt alternator under pully (20% under drive)

Thanks

drifter_sr

iTrader: (2)

ey brian.. i jus pm you man.. hope you can help me out with a map

BDC

Check your mail. Looks like I sent you one Monday night.

B