Haltech Post Haltech Base Map REQUESTS Here
#403
needs a cheaper hobby
iTrader: (4)
Join Date: Dec 2004
Location: Morgantown WV
Posts: 781
Likes: 0
Received 0 Likes
on
0 Posts
Can someone seems me a good timing map?
E8, 850/1600s. T78
S6, mild Street port, Ls coils, PFS big smic, 3" hks high power.
I'm most interested in a good solid timing map. The fuel trims on my map are semi reasonable, but whoever tuned it last had no idea what they were doing...
E8, 850/1600s. T78
S6, mild Street port, Ls coils, PFS big smic, 3" hks high power.
I'm most interested in a good solid timing map. The fuel trims on my map are semi reasonable, but whoever tuned it last had no idea what they were doing...
#404
Rotary Enthusiast
Looking for base map for 2nd gen tii.
Mods:
Fmic
Walbro
550cc primaries
1680cc secondaries
Removed emissions
Stock turbo
Stock coils
Running ps1k thanks email is bmwguy330@gmail.com
Mods:
Fmic
Walbro
550cc primaries
1680cc secondaries
Removed emissions
Stock turbo
Stock coils
Running ps1k thanks email is bmwguy330@gmail.com
#405
can anyone help me with the base map for fc3s s5 with ps1000
i got installed and already run the engine with base map sent by my dealer here in my country
but the engine cant get start when the temperature get hot (arround 70-90'C)
anyone can send me the base map with correction for the normal engine temperature please...
FYI : im using patch loom for my car...
but the engine cant get start when the temperature get hot (arround 70-90'C)
anyone can send me the base map with correction for the normal engine temperature please...
FYI : im using patch loom for my car...
#407
#408
Junior Member
iTrader: (2)
Join Date: Jun 2012
Location: Fort Knox
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
FC
13b
Turbonetics T04b turbo
Stock ignition
Dual walbro 255
Haltech on board map sensor
Stock tps
Haltech coolant temp and air temp sensors
RC 1200 primary low ohm
Bosch 1600 secondary low ohm
E85
Haltech platinum 1000
No bypass air control
If someone could help me out, I'd appreciate it. Thanks!
13b
Turbonetics T04b turbo
Stock ignition
Dual walbro 255
Haltech on board map sensor
Stock tps
Haltech coolant temp and air temp sensors
RC 1200 primary low ohm
Bosch 1600 secondary low ohm
E85
Haltech platinum 1000
No bypass air control
If someone could help me out, I'd appreciate it. Thanks!
#409
premix, for f's sake
iTrader: (6)
E6K
13b series 4, 6 port NA
medium/large street port, no aux sleeves (open 6 ports)
50mm ITB, DCOE style
AEM smart coils x4
4x 560cc low impedance injector (2 rpm based activation standoff/external injecotrs)
anything to get me started up and movable would be nice
thanks in advance
13b series 4, 6 port NA
medium/large street port, no aux sleeves (open 6 ports)
50mm ITB, DCOE style
AEM smart coils x4
4x 560cc low impedance injector (2 rpm based activation standoff/external injecotrs)
anything to get me started up and movable would be nice
thanks in advance
#411
Junior Member
iTrader: (1)
Join Date: Nov 2010
Location: DFW
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
I am looking for a base map for an Ek6
1. 6 port
2. Stock coils
3. Bridgeport
4. 500cc primaries, 1000cc secondaries
5. Electronic carb setup. RB lower intake
The engine is in a 82 corolla wagon.
We had a decent map going and the hard drive crashed and lost everything...didn't write anything down unfortunately.
Thank you
1. 6 port
2. Stock coils
3. Bridgeport
4. 500cc primaries, 1000cc secondaries
5. Electronic carb setup. RB lower intake
The engine is in a 82 corolla wagon.
We had a decent map going and the hard drive crashed and lost everything...didn't write anything down unfortunately.
Thank you
#412
'84 5-letter
iTrader: (5)
Not sure if this thread is ever checked any more, but figure its worth a shot.
Another request for NA maps. Don't seem to be too many floating around...
Another request for NA maps. Don't seem to be too many floating around...
- Haltech F9
- S5 6-port
- large streetport
- S5 intake / injectors (460cc primary & secondary)
- Racing Beat collected header for FB
- Stock GSL-SE ignition
#413
35r 13b first gen
iTrader: (3)
Join Date: Apr 2002
Location: Richland Center WI
Posts: 1,290
Likes: 0
Received 0 Likes
on
0 Posts
still looking for something for this...
the car is a 1985 GS...
it has 1987 13b for port.
I'm running a 4 barrel intake Jaytech brand..
autonomics 4 barrel throttle plate.. I believe it's around 6 to 700 cfm I'm not sure since they went out of business
I have ID 725 primaries and ID 2000 secondaries.. the fuel pump for now is an inline Walbro 255 lph I have 3/8 inch fuel lines feed and return have an aeromotive rising rate feul pressure regulator.. running 93 octane and premix...
I'm using an FC crank angle sensor. Greddy race plugs heat range 10 and 9. Four AEM smart oils.
I'm going to be running GM 3 bar map sensor GM intake air temp sensor GM coolant temp sensor. AEM wideband that I might tap into..
I have a Turblown stageV GT35r with true t4 housing wheel and flange.. custom Turblown short Runner exhaust manifold.. tile 44 millimeter waste gate 7.5 pound spring.. 3.5 inch downpipe and full straight through 3.5 in SS exhaust.. all 2.5 inch intercooler piping.. eBay front mount intercooler.. HKS SSQV blow off valve...
the car is a 1985 GS...
it has 1987 13b for port.
I'm running a 4 barrel intake Jaytech brand..
autonomics 4 barrel throttle plate.. I believe it's around 6 to 700 cfm I'm not sure since they went out of business
I have ID 725 primaries and ID 2000 secondaries.. the fuel pump for now is an inline Walbro 255 lph I have 3/8 inch fuel lines feed and return have an aeromotive rising rate feul pressure regulator.. running 93 octane and premix...
I'm using an FC crank angle sensor. Greddy race plugs heat range 10 and 9. Four AEM smart oils.
I'm going to be running GM 3 bar map sensor GM intake air temp sensor GM coolant temp sensor. AEM wideband that I might tap into..
I have a Turblown stageV GT35r with true t4 housing wheel and flange.. custom Turblown short Runner exhaust manifold.. tile 44 millimeter waste gate 7.5 pound spring.. 3.5 inch downpipe and full straight through 3.5 in SS exhaust.. all 2.5 inch intercooler piping.. eBay front mount intercooler.. HKS SSQV blow off valve...
#414
'84 5-letter
iTrader: (5)
still looking for something for this...
the car is a 1985 GS...
it has 1987 13b for port.
I'm running a 4 barrel intake Jaytech brand..
autonomics 4 barrel throttle plate.. I believe it's around 6 to 700 cfm I'm not sure since they went out of business
I have ID 725 primaries and ID 2000 secondaries.. the fuel pump for now is an inline Walbro 255 lph I have 3/8 inch fuel lines feed and return have an aeromotive rising rate feul pressure regulator.. running 93 octane and premix...
I'm using an FC crank angle sensor. Greddy race plugs heat range 10 and 9. Four AEM smart oils.
I'm going to be running GM 3 bar map sensor GM intake air temp sensor GM coolant temp sensor. AEM wideband that I might tap into..
I have a Turblown stageV GT35r with true t4 housing wheel and flange.. custom Turblown short Runner exhaust manifold.. tile 44 millimeter waste gate 7.5 pound spring.. 3.5 inch downpipe and full straight through 3.5 in SS exhaust.. all 2.5 inch intercooler piping.. eBay front mount intercooler.. HKS SSQV blow off valve...
the car is a 1985 GS...
it has 1987 13b for port.
I'm running a 4 barrel intake Jaytech brand..
autonomics 4 barrel throttle plate.. I believe it's around 6 to 700 cfm I'm not sure since they went out of business
I have ID 725 primaries and ID 2000 secondaries.. the fuel pump for now is an inline Walbro 255 lph I have 3/8 inch fuel lines feed and return have an aeromotive rising rate feul pressure regulator.. running 93 octane and premix...
I'm using an FC crank angle sensor. Greddy race plugs heat range 10 and 9. Four AEM smart oils.
I'm going to be running GM 3 bar map sensor GM intake air temp sensor GM coolant temp sensor. AEM wideband that I might tap into..
I have a Turblown stageV GT35r with true t4 housing wheel and flange.. custom Turblown short Runner exhaust manifold.. tile 44 millimeter waste gate 7.5 pound spring.. 3.5 inch downpipe and full straight through 3.5 in SS exhaust.. all 2.5 inch intercooler piping.. eBay front mount intercooler.. HKS SSQV blow off valve...
#415
Senior Member
May still be weeks away from start up, but will need a good base map to start out with.
Setup is:
PS1000
'93 FD
13B-rew pettit racing streetport
GM 3bar map sensor
750cc/2200cc injectors
Xcessive manufacturing LIM
stock UIM and throttle body
GM IAT sensor in Greddy elbow
OMP blocked off (premix in tank)
Aspec kit with PT6266 (vband inlet turbine)
expect to run about 20PSI boost
3" exhaust with High flow cat
4x IGN1A coils
MAC boost control solenoid
Pettit cool power intercooler kit.
Snow water/meth inj (want to tune to run with out it but use it for safety)
If there are any variables I left out let me know.
Thanks So Much in advance
Victor
Setup is:
PS1000
'93 FD
13B-rew pettit racing streetport
GM 3bar map sensor
750cc/2200cc injectors
Xcessive manufacturing LIM
stock UIM and throttle body
GM IAT sensor in Greddy elbow
OMP blocked off (premix in tank)
Aspec kit with PT6266 (vband inlet turbine)
expect to run about 20PSI boost
3" exhaust with High flow cat
4x IGN1A coils
MAC boost control solenoid
Pettit cool power intercooler kit.
Snow water/meth inj (want to tune to run with out it but use it for safety)
If there are any variables I left out let me know.
Thanks So Much in advance
Victor
Last edited by Vicoor; 04-28-13 at 02:32 PM.
#416
Senior Member
actually there are two things I see I left off.
FFE trigger wheel (rx8 style) with Hall effect sensor
AEM wide band O2 sensor
FFE trigger wheel (rx8 style) with Hall effect sensor
AEM wide band O2 sensor
Last edited by Vicoor; 04-28-13 at 08:23 PM.
#420
help with base map needed!
S4 stock port
gt35r
Haltech PS1K
4xIGN-1A
FFE trigger wheel
All haltech sensors
Stock BAC
4x ID1000
walbro 255
Especially the FFE/ign-1a/id1000/haltech sensors combo seems to be tricky to find...
what u think abt 350rwhp with this setup after final tune btw? possible on pump gas?
gt35r
Haltech PS1K
4xIGN-1A
FFE trigger wheel
All haltech sensors
Stock BAC
4x ID1000
walbro 255
Especially the FFE/ign-1a/id1000/haltech sensors combo seems to be tricky to find...
what u think abt 350rwhp with this setup after final tune btw? possible on pump gas?
#422
Junior Member
iTrader: (1)
Join Date: Jun 2008
Location: Louisiana
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
I'm running an e6k with 550/850 injectors. I have a map I modified after downloading from the Hitman years ago. I'm also using a t03/04 hybrid.
If this is similar to your setup then it may be a good starting point. Let me know if you still need a map.
If this is similar to your setup then it may be a good starting point. Let me know if you still need a map.