Coming along real nice!

 

So the sunroof had some rust/ holes.. Wasn't very nice... Now that being said the repair/bondo job I did with black gloss paint doesn't look to swell either , so I'm going to cover it in sticker!

 

Drum roll please...... It's in! So after much difficulty and waiting it's finally in the car!

 

Took some time to jimmy the motor and tranny in... but we did it... then found out i had no tranny mount bolts -_- doh.. so found one bolt that would fit for now snugged it up and off to the hardware store for some bolts!,now its time to slowly wire it all back up, install the fuel rails, finish up with me AEM FIC 6 install, and then next project is to finish up the exhaust, must hunt down a exhaust shop that doesnt cost a arm and a leg.. other then that, its slowly coming together, im thinking i should upgrade my secondarys once i get it running smooth, so i can add alittle bit more fuel, after 6-8 psi, i will see how it reacts, this hybrid turbo is good to push 14ish psi, but im unsure how much my 6port HC (highcompressoin) 13b will do. so its time to slowly take my time and get it all right!

 

Great build love the purple im hanging in for the ride

 

Thanks! It's a dirty metallic flake purple!

 

Patience is what brings it together, dill. Looking good. Hopefully you won't find any annoying wiring gremlins like I have.

 

Dig the color scheme of the keg and manifolds. Was goin bronze also til I could find the exact dark bronze that I wanted . So red it was . Hopefully I'll be finally running next week or so . Can't wait to see you 6pt running .as far as boost I hit 8-10 so far on the old setup with no problems . I'm hoping to run 10-12 for a lil bit and go from there . I know it will pop one day , just wanna atleast drive It for a lil bit before I crank it up lol

 

Thanks man! Yea I hear yea, blah, working under the car when it's only so high sucks.. My roomates using the stands so I get to crawl under to finish the tranny mount bolts -_- super gay. On a other note tomorrow I get to take the drive shaft off and then on again.. Haha didn't have time to attach it to the tranny when putting the motor in

 

What turbo setup are you running?

 

E6k, 800 primes,1600 sec's , walbro , holset hx52 , etc ...

 

Sounds fast

 

I want it to scare me , that's my goal . Hopefully this time it will .and just a pic

 

looks clean

 

I got a sunroof for ya Pickle...(funny,it was sitting in the same spot as that rad!)

Going to this?..it's about 20 minutes from you.
https://www.rx7club.com/canadian-for...1057804/page2/

 

s

I can make an appearance , the purple bastard won't be running :/

 

Update, installed driveshaft, reinstalled presilencer and Y, now to just wait to get my mufflers fabbed up to bolt right on. Now.. Does anyone know if there's a right up or a video on how to reinstall a engine harness.. My t2 engine harness is just chilling and I have no idea where to start..

 

Starting to plug around ... Anyone know how to make a s4 t2 intercooler fit on a s5 UIM?


Relocated, window switch and mirrors in the center console.. Also have hks boost controller ready for set up, couple more parts to get.. T2 compression tube pressure sensor, rad hoses, omp delete, turbo feed/oil plate, bov unless I cap and not run one and that's about it I do believe!

 

Exhaust is welded up and installed! Ordered my camber plates from FAL! And my OMP delete and my turbo feed kit! So getting close!

 

Front plates ? Looking awesome brotha . I just finished yesterday in the bay . And finally downloaded my base map . Going to charge the battery and give it a crank

 

Yea front camber plates my grand marqui wheels stick out a weeeee bit haha and sorry! Let me know how it goes!

 

How's those door panels coming along . What did you make them out of by chance ?

 

. Corrugated plastic, they turned out not bad for prototypes I would like too make another set but there good enough for now!

 

Update, Camber plates, omp delete, and turbo feed kit is sitting in ogdensburg waiting for me other then that, slowly connecting everything going to need some rad hoses for start up, so im running around looking for the best deal, other then that, going to pick up a grip royal steering wheel on friday woot

 

Update... It runs, after a lot of changes to the car, it's now running a lt8 microtech, it started after acouple cranks and idles timing is a little off but will fix that later Have some exhaust leaks I need to fix aswell as some wiring todo aswell as we made a full engine harness in one day! But after 7 months of the car not running she started up no problem!