first time rx7 build, always looking for advice!
#54
Took some time to jimmy the motor and tranny in... but we did it... then found out i had no tranny mount bolts -_- doh.. so found one bolt that would fit for now snugged it up and off to the hardware store for some bolts!,now its time to slowly wire it all back up, install the fuel rails, finish up with me AEM FIC 6 install, and then next project is to finish up the exhaust, must hunt down a exhaust shop that doesnt cost a arm and a leg.. other then that, its slowly coming together, im thinking i should upgrade my secondarys once i get it running smooth, so i can add alittle bit more fuel, after 6-8 psi, i will see how it reacts, this hybrid turbo is good to push 14ish psi, but im unsure how much my 6port HC (highcompressoin) 13b will do. so its time to slowly take my time and get it all right!
#58
NA-BOOSTIN
Dig the color scheme of the keg and manifolds. Was goin bronze also til I could find the exact dark bronze that I wanted . So red it was . Hopefully I'll be finally running next week or so . Can't wait to see you 6pt running .as far as boost I hit 8-10 so far on the old setup with no problems . I'm hoping to run 10-12 for a lil bit and go from there . I know it will pop one day , just wanna atleast drive It for a lil bit before I crank it up lol
#59
Dig the color scheme of the keg and manifolds. Was goin bronze also til I could find the exact dark bronze that I wanted . So red it was . Hopefully I'll be finally running next week or so . Can't wait to see you 6pt running .as far as boost I hit 8-10 so far on the old setup with no problems . I'm hoping to run 10-12 for a lil bit and go from there . I know it will pop one day , just wanna atleast drive It for a lil bit before I crank it up lol
#60
Dig the color scheme of the keg and manifolds. Was goin bronze also til I could find the exact dark bronze that I wanted . So red it was . Hopefully I'll be finally running next week or so . Can't wait to see you 6pt running .as far as boost I hit 8-10 so far on the old setup with no problems . I'm hoping to run 10-12 for a lil bit and go from there . I know it will pop one day , just wanna atleast drive It for a lil bit before I crank it up lol
What turbo setup are you running?
#65
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
I got a sunroof for ya Pickle...(funny,it was sitting in the same spot as that rad!)
Going to this?..it's about 20 minutes from you.
https://www.rx7club.com/canadian-for...1057804/page2/
Going to this?..it's about 20 minutes from you.
https://www.rx7club.com/canadian-for...1057804/page2/
Last edited by misterstyx69; 06-06-14 at 12:17 AM.
#66
I got a sunroof for ya Pickle...(funny,it was sitting in the same spot as that rad!) Going to this?..it's about 20 minutes from you. https://www.rx7club.com/canadian-for...1057804/page2/
I can make an appearance , the purple bastard won't be running :/
#67
Update, installed driveshaft, reinstalled presilencer and Y, now to just wait to get my mufflers fabbed up to bolt right on. Now.. Does anyone know if there's a right up or a video on how to reinstall a engine harness.. My t2 engine harness is just chilling and I have no idea where to start..
#68
Starting to plug around ... Anyone know how to make a s4 t2 intercooler fit on a s5 UIM?
Relocated, window switch and mirrors in the center console.. Also have hks boost controller ready for set up, couple more parts to get.. T2 compression tube pressure sensor, rad hoses, omp delete, turbo feed/oil plate, bov unless I cap and not run one and that's about it I do believe!
Relocated, window switch and mirrors in the center console.. Also have hks boost controller ready for set up, couple more parts to get.. T2 compression tube pressure sensor, rad hoses, omp delete, turbo feed/oil plate, bov unless I cap and not run one and that's about it I do believe!
#74
Update, Camber plates, omp delete, and turbo feed kit is sitting in ogdensburg waiting for me other then that, slowly connecting everything going to need some rad hoses for start up, so im running around looking for the best deal, other then that, going to pick up a grip royal steering wheel on friday woot
#75
Update... It runs, after a lot of changes to the car, it's now running a lt8 microtech, it started after acouple cranks and idles timing is a little off but will fix that later Have some exhaust leaks I need to fix aswell as some wiring todo aswell as we made a full engine harness in one day! But after 7 months of the car not running she started up no problem!