3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

wont Start

Thread Tools
 
Search this Thread
 
Old 06-09-06, 11:18 AM
  #1  
Newbie
Thread Starter
 
Bcollins's Avatar
 
Join Date: Feb 2006
Location: Freehold Nj
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
wont Start

the other day i went to start the car up and the starter was working fine but when the car went to turn over it only barely started smoked alot and turnd off.... i tried to start it again and they same thing happened... the fuel level was a little low so i went and filled the tank but it still wont turn over completely, smoked alot then turned off also i noticed a little oil leaking from under the car ... just wondering if anyone knows what is going on or knows how to fix it .
bryan
Old 06-09-06, 07:37 PM
  #2  
Rotary Restorer

iTrader: (6)
 
salva's Avatar
 
Join Date: Jul 2005
Location: Central FL
Posts: 390
Likes: 0
Received 0 Likes on 0 Posts
Probably flooded. Rmove your sprk plugs and check if they are wet w/fuel, if so then you need to remove the EFI relay and crank it over without the plugs a few seconds to remove fuel in engine. Clean the plugs w/ carb cleaner, let dry, then reinstall both plugs and relay and give it a try.
Old 06-10-06, 08:16 AM
  #3  
Newbie
Thread Starter
 
Bcollins's Avatar
 
Join Date: Feb 2006
Location: Freehold Nj
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
thanks ... ill give it a shot today and let you know how it goes
Old 06-10-06, 10:15 AM
  #4  
Rotary Restorer

iTrader: (6)
 
salva's Avatar
 
Join Date: Jul 2005
Location: Central FL
Posts: 390
Likes: 0
Received 0 Likes on 0 Posts
If it still does not start you may need o get new plugs, and go through the same process.
Old 06-11-06, 11:14 AM
  #5  
Newbie
Thread Starter
 
Bcollins's Avatar
 
Join Date: Feb 2006
Location: Freehold Nj
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
how do i disconnect the EFI relay
Old 06-11-06, 12:36 PM
  #6  
Rotary Restorer

iTrader: (6)
 
salva's Avatar
 
Join Date: Jul 2005
Location: Central FL
Posts: 390
Likes: 0
Received 0 Likes on 0 Posts
The relay is in the relay and fuse block next to the driver shock tower. Open it up and it is the upper right square shaped relay, I believe it's yellow. Pull it out carefully, you might need to pry it out but be carefull not to crack it. If in doubt download the Shop manual Under 3rd Gen section and see page Z-29, it is the one labled B1-02 (Main EGI relay).
Old 06-11-06, 12:39 PM
  #7  
Rotary Restorer

iTrader: (6)
 
salva's Avatar
 
Join Date: Jul 2005
Location: Central FL
Posts: 390
Likes: 0
Received 0 Likes on 0 Posts
The relay is in the relay and fuse block next to the driver shock tower. Open it up and it is the upper right square shaped relay, I believe it's yellow. Pull it out carefully, you might need to pry it out but be carefull not to crack it. If in doubt download the Shop manual Under 3rd Gen section and see page Z-29, it is the one labled B1-02 (they call it the Main EGI relay).
Old 06-11-06, 02:30 PM
  #8  
rotor rotor pow.

iTrader: (1)
 
sevensix's Avatar
 
Join Date: Mar 2005
Location: Southern CA
Posts: 3,170
Received 1 Like on 1 Post
cant he just pull one in the fuse box at the + terminal
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
ZacMan
Build Threads
4
09-19-15 09:20 PM
sherff
Adaptronic Engine Mgmt - AUS
5
09-12-15 12:22 PM
whinin
New Member RX-7 Technical
10
09-05-15 11:52 PM



Quick Reply: wont Start



All times are GMT -5. The time now is 03:47 PM.