3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

wont Start

Old Jun 9, 2006 | 11:18 AM
  #1  
Bcollins's Avatar
Thread Starter
Newbie
 
Joined: Feb 2006
Posts: 4
Likes: 0
From: Freehold Nj
wont Start

the other day i went to start the car up and the starter was working fine but when the car went to turn over it only barely started smoked alot and turnd off.... i tried to start it again and they same thing happened... the fuel level was a little low so i went and filled the tank but it still wont turn over completely, smoked alot then turned off also i noticed a little oil leaking from under the car ... just wondering if anyone knows what is going on or knows how to fix it .
bryan
Reply
Old Jun 9, 2006 | 07:37 PM
  #2  
salva's Avatar
Rotary Restorer
Tenured Member: 20 Years
iTrader: (6)
 
Joined: Jul 2005
Posts: 390
Likes: 0
From: Central FL
Probably flooded. Rmove your sprk plugs and check if they are wet w/fuel, if so then you need to remove the EFI relay and crank it over without the plugs a few seconds to remove fuel in engine. Clean the plugs w/ carb cleaner, let dry, then reinstall both plugs and relay and give it a try.
Reply
Old Jun 10, 2006 | 08:16 AM
  #3  
Bcollins's Avatar
Thread Starter
Newbie
 
Joined: Feb 2006
Posts: 4
Likes: 0
From: Freehold Nj
thanks ... ill give it a shot today and let you know how it goes
Reply
Old Jun 10, 2006 | 10:15 AM
  #4  
salva's Avatar
Rotary Restorer
Tenured Member: 20 Years
iTrader: (6)
 
Joined: Jul 2005
Posts: 390
Likes: 0
From: Central FL
If it still does not start you may need o get new plugs, and go through the same process.
Reply
Old Jun 11, 2006 | 11:14 AM
  #5  
Bcollins's Avatar
Thread Starter
Newbie
 
Joined: Feb 2006
Posts: 4
Likes: 0
From: Freehold Nj
how do i disconnect the EFI relay
Reply
Old Jun 11, 2006 | 12:36 PM
  #6  
salva's Avatar
Rotary Restorer
Tenured Member: 20 Years
iTrader: (6)
 
Joined: Jul 2005
Posts: 390
Likes: 0
From: Central FL
The relay is in the relay and fuse block next to the driver shock tower. Open it up and it is the upper right square shaped relay, I believe it's yellow. Pull it out carefully, you might need to pry it out but be carefull not to crack it. If in doubt download the Shop manual Under 3rd Gen section and see page Z-29, it is the one labled B1-02 (Main EGI relay).
Reply
Old Jun 11, 2006 | 12:39 PM
  #7  
salva's Avatar
Rotary Restorer
Tenured Member: 20 Years
iTrader: (6)
 
Joined: Jul 2005
Posts: 390
Likes: 0
From: Central FL
The relay is in the relay and fuse block next to the driver shock tower. Open it up and it is the upper right square shaped relay, I believe it's yellow. Pull it out carefully, you might need to pry it out but be carefull not to crack it. If in doubt download the Shop manual Under 3rd Gen section and see page Z-29, it is the one labled B1-02 (they call it the Main EGI relay).
Reply
Old Jun 11, 2006 | 02:30 PM
  #8  
sevensix's Avatar
rotor rotor pow.
Tenured Member 15 Years
iTrader: (1)
 
Joined: Mar 2005
Posts: 3,170
Likes: 1
From: Southern CA
cant he just pull one in the fuse box at the + terminal
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
ZacMan
Build Threads
4
Sep 19, 2015 09:20 PM
sherff
Adaptronic Engine Mgmt - AUS
5
Sep 12, 2015 12:22 PM
whinin
New Member RX-7 Technical
10
Sep 5, 2015 11:52 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 05:53 PM.