What type of intake system do you have?
#1
What type of intake system do you have?
I am sure there has been a poll on this, but I missed it!
And the search engine sucks!
please let me know, Am asking b/c quite frankly, I have an m2 and the fitment is horriable. I want one that will allow good flow but also fits nicely, Everyone's concept am sure. I just want to know what YOU 7 ethusiast have.
thanks in advance.
And the search engine sucks!
please let me know, Am asking b/c quite frankly, I have an m2 and the fitment is horriable. I want one that will allow good flow but also fits nicely, Everyone's concept am sure. I just want to know what YOU 7 ethusiast have.
thanks in advance.
#4
Senior Member
Join Date: Oct 2001
Location: Minnesota, now in FL and I dont think I'm goin back
Posts: 443
Likes: 0
Received 0 Likes
on
0 Posts
I have the Blitz SUS intake, again the instructions sucked but its really a super easy insall. It also looks really nice, and does not wear out because it is mesh.
Mike
Mike
Trending Topics
#10
Rotary Enthusiast
Join Date: Feb 2002
Location: Frisco, Texas
Posts: 828
Likes: 0
Received 0 Likes
on
0 Posts
I also have the Apex'i Power Intake. Looks great, works great, fits great. The only problem I have with it is I am limited in what Intercooler I can upgrade to when I upgrade.
#12
Rotary Freak
I had the RE Amemiya Intake, but was forced to get another intake when I got my Huge M2/ASP SMIC.
I made my own custom cold air intake using two 3x6" cylindrical K&N filters(the same as the ones used in the Pettit intake).
I also ran two 3" ducts from the nose of the car to the K&N's and fabbed an aluminum(polished) heat shield.
I made my own custom cold air intake using two 3x6" cylindrical K&N filters(the same as the ones used in the Pettit intake).
I also ran two 3" ducts from the nose of the car to the K&N's and fabbed an aluminum(polished) heat shield.
#15
I have a similar custom K&N setup to RyanREX. BTW, the search engine doesn't suck too bad, there have been tons of posts on intakes recently. I was looking up a bunch of info within the past month and didn't have any trouble finding what I needed.
#16
Speed Mach Go Go Go
iTrader: (2)
Join Date: Oct 2001
Location: My 350Z Roadster kicks my RX7's butt
Posts: 4,772
Likes: 0
Received 2 Likes
on
2 Posts
I have the Blitz. I love the looks, the sound and response and it comes with a heat sheald.
If you want to do the "DIY" K&N deal. You can make it similar to the Pettit buy purchasing this RE Amemiya heat shield from jt-imports.com
Ack, stupid Netscape, damn firewalls.
You'll have to fo to the site and look it up.
If you want to do the "DIY" K&N deal. You can make it similar to the Pettit buy purchasing this RE Amemiya heat shield from jt-imports.com
Ack, stupid Netscape, damn firewalls.
You'll have to fo to the site and look it up.
#18
first, The bottom of the m2's box where the second turbo piping is surpose to go to is to low , thus makeing the rubber factory hose bend more than what is consider good. As a matter of fact, I think my motor may have went because of it. first the intake would bent under heavy throttle and all of a sudden the intake pipe would be reduce in efficiency, AND maybe that cause a problem. and so on .. Second the box should of been just a little bit bigger in demention so that the intake will have more area to take in air.
2cent
2cent
Thread
Thread Starter
Forum
Replies
Last Post