Secondary boost problem
#1
Senior Member
Thread Starter
Join Date: Aug 2002
Location: Hawaii
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
Secondary boost problem
I tried search but i couldn't find any combination of words that described my problem. My primary turbo spools fine to 10 psi however when the secondary hits it drops to 5 and then goes to 7 then begins to sputter between 7 and 5 psi it does this at WOT.. anyone by chance have a similar problem and were able to solve it? thank you
#2
il Cosa Nostra e vivo!!
iTrader: (1)
Join Date: May 2003
Location: Dove le cose sono fatte il vecchio moda il senso
Posts: 2,097
Likes: 0
Received 0 Likes
on
0 Posts
Try changing/crossing the electrical plugs (not the vacuum hoses) on the Pre-Control/Wastegate solenoid. This is the "double" solenoid that is located underneath and in front of the UIM. I had the same problem of not boosting over 7 psi after secondary transition. I crossed them and immediately obtained 10-12-10 pattern. Good Luck.
#5
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
Could be a vaccum related issue.(vaccum hose related) What is the milage on your car? Are your Intercooler couplers original?(specifically the y-pipe to IC crossover) Have you had the silicon hose replacement job done? Lots of little things to check.... make sure you switch the pre-control and wastegate control connectors back to their original positions.
#6
Rotary Freak
Join Date: Dec 2002
Location: Slovenia, Europe
Posts: 2,522
Likes: 0
Received 0 Likes
on
0 Posts
I have the same problem. Primary boosts fine and then secondary only does 7-8psi (at transition it falls down to 5psi). Could this be caused by a clogged pre-cat ?
Anyway I'm installing a DP in coming days and we'll see. Otherwise I'll just have to find the culprit.
Anyway I'm installing a DP in coming days and we'll see. Otherwise I'll just have to find the culprit.
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Aug 2002
Location: Hawaii
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
i've done a vac job to the car and i have an efini ypipe ... my friend was kind enough to give me a new coupler the one from the ypipe to the intercooler.. like when it transitions it ends up fluttering like 10-5-7-5-7 until i hit redline
the car has around 56k on it
the car has around 56k on it
#9
Chasing numbers
iTrader: (5)
I started having the same boost problem this weekend. Seems like the presure (boost) just drops right when the second one wants to come on. I am sure this must be a common thing on our cars I have heard this problem too many times. I have not upgraded anything in over a year that could or would affect the boost. Seems like a vaccum leak, or something else just came off. Anyone??
#10
Eats, Sleeps, Dreams Rotary
iTrader: (4)
Join Date: Apr 2003
Location: Denver, NC
Posts: 3,531
Likes: 0
Received 0 Likes
on
0 Posts
Do you hear any fluttering in the exhaust note? Is your exhaust stock? I had a CCA that was going bad and fluttered when the transition to the secondary occured.(When the flapper valve in the y-pipe opens)I could hear the valve flutter in the exhaust note.(full exhaust) I also had a valve get sticky after cleaning it. Just added some tri-flo lube to the pivot points and it was ok.
#14
Senior Member
Join Date: Jul 2002
Location: Los Alamos, NM
Posts: 592
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by patriick
http://www.autosportracetech.com/RX-...leshooting.htm
http://www.autosportracetech.com/RX-...leshooting.htm
Check: couplers, hoses, solenoids, valves, actuators.
If they all seem fine, do some T-tests.
Then come back and tell us what the problem was.
Good luck
#15
Chasing numbers
iTrader: (5)
Ok, I replaced all vacuum lines (this time with silicon, Cam recommended goodyear rubber last time) I also checked the check valves. The only test I was concerned about was the CCA. Test says start car let warm up verify that arm on CCA is in, turn off car pull vac line and arm should come out. Mine comes out as soon as car is turned off? Also I noticed my car is low on the vacuum at idle, 11-12hg instead of 17-19 in the past. So must be a vac leak but I just did a hose job?? Could there be a actuator leaking internally? I also installed a new y-pipe to eliminate that issue.
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM