3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Power???

Thread Tools
 
Search this Thread
 
Old Apr 13, 2004 | 08:54 PM
  #1  
Fred Villamor's Avatar
Thread Starter
Rotary Freak
Tenured Member 15 Years
 
Joined: Aug 2003
Posts: 1,633
Likes: 0
From: Pensacola, Fla.
Power???

Iv'e recently finished a wave of mods to my 93 RX7 and I was curious as to how much HP I am getting ?? (ballpark guesstimate???) Power Fc & commander , M2 downpipe , RX7 store resonated midpipe , Apexi N-1 cat back , full blockplate kit , Non-sequential conversion (parallel turbos) , removal of airpump and ratsnest (solenoids) , hardpipe intake with KNN filters , Rotary Performance stage 2 clutch kit , Approx. 11lbs of boost ( right now ) Does anyone have an estimate on HP from some comparably modded cars ?? Also , I just got a set of 1300 cc injectors to put in the 2ndary rail and I got an RX7store primary rail to fit my 850s into , with the Nippondenso fuel pump upgrade , that hasn't been installed yet . Anyone have an idea of HP w/out the fuel pump and injector installation ?? I don't have a Dyno anywhere near me to find out for sure . Thanks for any help any of you may have...Cya
Reply
Old Apr 13, 2004 | 10:02 PM
  #2  
fastcarfreak's Avatar
3rd motors a charm I hope
Tenured Member 15 Years
 
Joined: Apr 2003
Posts: 2,054
Likes: 0
From: Central New York
i would say about 50+ to the wheels for everything. Your gonna feel a huge difference in your car man. get it tuned though.

Last edited by fastcarfreak; Apr 13, 2004 at 10:04 PM.
Reply
Old Apr 13, 2004 | 11:11 PM
  #3  
Fred Villamor's Avatar
Thread Starter
Rotary Freak
Tenured Member 15 Years
 
Joined: Aug 2003
Posts: 1,633
Likes: 0
From: Pensacola, Fla.
50 + , is that it ? DAMNNNN!! I was hoping for more than that with all the $$$ spent on this stuff. What about tuning ? Are you talking about Datalogging , or what else ? Thanks FV
Reply
Old Apr 13, 2004 | 11:16 PM
  #4  
Fred Villamor's Avatar
Thread Starter
Rotary Freak
Tenured Member 15 Years
 
Joined: Aug 2003
Posts: 1,633
Likes: 0
From: Pensacola, Fla.
We had a couple of boost runs when first dialing the boost pressure where we reached 14 +psi and hit a fuel cut , so we increased the rev limiter to like 10,000 rpms and dialed the boost down to 11psi to start with. It was such a noticable difference that I was way happy with the way it felt so I left it there (11psi) . If I increase it back to 14psi , approx. how much HP would you guesstimate then ?? Thanks again FV
Reply
Old Apr 13, 2004 | 11:56 PM
  #5  
PVerdieck's Avatar
Rotary Freak
Tenured Member 10 Years
 
Joined: May 2002
Posts: 1,742
Likes: 0
From: Houston
What you have is a lot of potential, and not much else.

What you need is a good tuning. By someone that knows a PFC. You need to head to Pettit, and have them tune it, or something like that.

You have made a serious bunch of mods to your machine, but without someone to properly tune it, you don't have the complete package.

You should be 350-375 when tuned, or thereabouts with that setup. But you won't see it until....
Reply
Old Apr 14, 2004 | 12:01 AM
  #6  
TAMAatWork's Avatar
Senior Member
Tenured Member 05 Years
 
Joined: Feb 2002
Posts: 258
Likes: 0
From: Austin, TX
No intercooler?

-Joseph
Reply
Old Apr 14, 2004 | 08:24 AM
  #7  
Fred Villamor's Avatar
Thread Starter
Rotary Freak
Tenured Member 15 Years
 
Joined: Aug 2003
Posts: 1,633
Likes: 0
From: Pensacola, Fla.
FMIC is the next piece , I got a new radiator already , but can,t fit it in stock location until I get the front mount ...2 * 1/16th inch core !! Is the tuning done with the datalogit? Thanks for all the help guys...FV
Reply
Old Apr 14, 2004 | 08:56 AM
  #8  
1QWIK7's Avatar
White chicks > *
Tenured Member: 20 Years
iTrader: (33)
 
Joined: Jul 2003
Posts: 13,146
Likes: 1
From: Secaucus, New Jersey
yeah bout 50 to the wheels sounds somewhat correct, remember thats to the wheels!!

def get it tuned though, otherwise those extra 50 horses will feel like sh*t..
Reply
Old Apr 14, 2004 | 09:19 AM
  #9  
P'cola FD's Avatar
Hamado things my way!
Tenured Member 10 Years
 
Joined: Oct 2001
Posts: 1,245
Likes: 0
From: Pensacola, Florida
Fred, since you're in Pensacola, do you know Rodney? He works at V&T Performance. He's tuned his PFC for his T04R with the dataloggit he has. He may be willing to tune your car in his spare time for some cheddar. PM me if you want his number.
Reply
Old Apr 14, 2004 | 11:56 AM
  #10  
Fred Villamor's Avatar
Thread Starter
Rotary Freak
Tenured Member 15 Years
 
Joined: Aug 2003
Posts: 1,633
Likes: 0
From: Pensacola, Fla.
I know Rodney , he's alredy done some work for me. I thought about him ,
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
rgordon1979
3rd Generation Specific (1993-2002)
40
Mar 15, 2022 12:04 PM
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
High_Carb_Diet
Power FC Forum
1
Sep 5, 2015 09:07 AM




All times are GMT -5. The time now is 09:26 PM.