What do YOU want made for YOUR FC???
#182
Originally posted by RotaryResurrection
Finally, I'd like to see a pre-made oil filter relocation kit for the FC (as well as GSLSE and FD) including lines and hardware, a bolt on affair. Move the oil filter down so it is accessible from under the car, just like the oil drainplug. I hate to build a clean engine then get the ****** all dirty with oil running everywhere from mazda's stupid oil filter location. Plus, this could be integrated with a setup like the racing beat, mazdatrix, and fc3s.org oil filter pedestal adaptors which allow you to run aftermarket sending units. Something in the $50-150 range would be acceptable.
I'll probably think of more...
Finally, I'd like to see a pre-made oil filter relocation kit for the FC (as well as GSLSE and FD) including lines and hardware, a bolt on affair. Move the oil filter down so it is accessible from under the car, just like the oil drainplug. I hate to build a clean engine then get the ****** all dirty with oil running everywhere from mazda's stupid oil filter location. Plus, this could be integrated with a setup like the racing beat, mazdatrix, and fc3s.org oil filter pedestal adaptors which allow you to run aftermarket sending units. Something in the $50-150 range would be acceptable.
I'll probably think of more...
#183
Originally posted by Josepi
They make them...and I don't know exactly why you'd need one...
They make them...and I don't know exactly why you'd need one...
#184
Lives on the Forum
Thread Starter
Originally posted by vrooom305
because I have an automatic and I don't want to buy a manual transmission with xxx,xxx amount of miles on it. But please do tell where I can get one!
because I have an automatic and I don't want to buy a manual transmission with xxx,xxx amount of miles on it. But please do tell where I can get one!
-Ted
#186
Senior Member
Join Date: Mar 2004
Location: Cleveland
Posts: 458
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by RETed
$100?
polished aluminum pipe
2 or 3 layer reinforced silicone hoses, in three colors (blue, yellow, red)
-Ted
$100?
polished aluminum pipe
2 or 3 layer reinforced silicone hoses, in three colors (blue, yellow, red)
-Ted
Yes, would buy. Hopfuly a little cheaper, but if cost make the price $100, then I think I would buy.
#187
Senior Member
Join Date: Mar 2004
Location: Cleveland
Posts: 458
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by JerryLH3
I've thought of another one. I think I saw pedals mentioned, but I'll be even more specific.
These pedals were made by Sled Driver, but he had to stop production, as work wouldn't let him continue using their machine. See if it's possible to get the exact specs from him and duplicate them. I'd pay what he was asking.
I've thought of another one. I think I saw pedals mentioned, but I'll be even more specific.
These pedals were made by Sled Driver, but he had to stop production, as work wouldn't let him continue using their machine. See if it's possible to get the exact specs from him and duplicate them. I'd pay what he was asking.
Last edited by Wizz; 03-24-04 at 10:48 PM.
#188
Full Member
iTrader: (1)
Join Date: Jun 2007
Location: NEW JERSEY
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
i would like a plug and play wiring for the engine bay and for the dash, i'm tired of fixing someone else's mess up or miss connection. and i think 80-100 dollers depending on how well the kits are made.
#190
I would like a beefed up alternator that is plug and play $200.
Also any parts offered for a 240 $??.
Front 4 pot calipers without that stupid knub sticking out $60 different colors available.
An upgraded proper functioning tps $70.
Some kind of separate premix design that allows to fill a reservoir that mixes off vacuum that is adjustable $200.
A bolt in harness bar $150.
A spool for the rear end $300.
Pre-grinded side seals for all different sizes $50 each.
Also any parts offered for a 240 $??.
Front 4 pot calipers without that stupid knub sticking out $60 different colors available.
An upgraded proper functioning tps $70.
Some kind of separate premix design that allows to fill a reservoir that mixes off vacuum that is adjustable $200.
A bolt in harness bar $150.
A spool for the rear end $300.
Pre-grinded side seals for all different sizes $50 each.
#195
#196
Trunk Ornament
iTrader: (11)
Make a nacaduct like the miatas do.
http://www.weekend-racer.com/spec-mi...ows-p_313.html
http://www.weekend-racer.com/spec-mi...ows-p_313.html
And I'm pretty sure this thread expired before Justin Bieber was born.