what do u use after ditching the washer resivour when you did your FMIC install?
#1
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
what do u use after ditching the washer resivour when you did your FMIC install?
ill prob use the hole where the resivour was (for a FMIC install) but, i NEED the washer fluid and wondered what you did to retain or replace it??
if you found somethin else to replace it please supply a good link or somthin to show what you used...
if you found somethin else to replace it please supply a good link or somthin to show what you used...
#2
zZzZzZzZzZz..............
iTrader: (12)
eerrr....for my cars fmic... the route on the passenger side/washer fluid side went under the car and straight up to have a big "U-turn" to go back down to the turbo, so it doesnt go into the engine bay from the washer fluid place but a little behind the intake....
sorry for the bad explanation, hope u can picture it
sorry for the bad explanation, hope u can picture it
#3
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
thats how i have mine now and i ended up cutting into my under belly tray...
i prob. could have gotten away without having to do that....
im just thinkin that it would be shorter this way...
i prob. could have gotten away without having to do that....
im just thinkin that it would be shorter this way...
#6
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by robtechfabrications
rainx is your friend
LOL, i tried that stuff, it was .99 cents for a little packet, put it in my washer fluid...hated it...i just dont like that stuff...
im sure someone figured a way to either relocate it or found a replacement...
*edit* wait a sec...i NEVER use the rear window resivour??? HMMMMM??
#7
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
Why not use a Cold start Bottle,and Rig up an inline washer Pump..You should be able to do it very easily .And it will sort of look Stock too!
Trending Topics
#8
Rotary Enthusiast
Join Date: May 2005
Location: bartlett IL
Posts: 919
Likes: 0
Received 0 Likes
on
0 Posts
You could also use the headlight washer bottle from an S5 or 10th AE and run the rubber hose and electric to it. The junkyard or classifieds in the forum are your friend for this solution. And FYI rain-X should be applied directly to the window with a rag (unless they came out with a new product that I have not seen yet)?
#10
Passing life by
I used stock hole and custom mounted my resivour. Cut out hole for IC pipe next to OEM hole.
On my project FC all resivours have been moved to where the RAD over flow is in that area between the core support. I have the over flow, washer bottle, Alcy injection. Now I am just trying to find a way to run the RA 2 cycle injection kit with my motor and run that under there also.
Hope that gave you some ideas.
On my project FC all resivours have been moved to where the RAD over flow is in that area between the core support. I have the over flow, washer bottle, Alcy injection. Now I am just trying to find a way to run the RA 2 cycle injection kit with my motor and run that under there also.
Hope that gave you some ideas.
#11
Senior Member
iTrader: (5)
Join Date: Aug 2003
Location: Kitchener, ON
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
Just use the cold start bottle. I just converted mine. It's big enough, you just have to check it more often. All you have to do is run a wire from the washer bottle connector to the cold start bottle. Check to make sure the motor turns however. Mine may never have moved in 15 years and so didn't turn. i had to take it apart and free up the shaft. Now it works fine!
#13
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
the trashman to my cold start assist bottle.....DAMN! i think i might just custom mount the rear bottle since i never fill it anyway and the motor still works...but these are good ideas!
#14
Rattle can retard
Join Date: Jul 2001
Location: St. Peters, MO
Posts: 660
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by tinvestor
And FYI rain-X should be applied directly to the window with a rag (unless they came out with a new product that I have not seen yet)?
the stuff in the little squeeze bottle that you apply with a rag works well. you just have to reapply it every couple/few months.
but rain-x isn't designed to keep dirt off your windshield, it's designed to displace water. so it's not a valid solution.
#16
I live in the lounge...
Join Date: Aug 2004
Location: lathrup, MI
Posts: 2,000
Likes: 0
Received 0 Likes
on
0 Posts
i just pulled the lines bottle squirters and everything. never had a problem, even on my 1200mile road trip. just be shure to clean it at gas stations every now and then on road trips. or once a week normal driving.
#17
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by HAILERS
I've a GREEDY and didn't have to move the washer bottle. Works just fine as original.
#18
needs an FD
Join Date: Dec 2005
Location: sacramento
Posts: 755
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Flobb
but rain-x isn't designed to keep dirt off your windshield, it's designed to displace water. so it's not a valid solution.
i've used rainx for years...i dont even remember the last time i had wipers on my car and used them.
clean the living hell out of your windshield...get a clean white cloth and rub on rainx in a circular motion. wait til it get cloudy on your windshield...wipe off with a clean white cloth in a circular motion...repeat 2-3x
water will not stick to your windshield
#19
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes
on
19 Posts
Originally Posted by 88rxn/a
how is it ran then?? the hotside of the IC?
Thread
Thread Starter
Forum
Replies
Last Post
tiger18
3rd Generation Specific (1993-2002)
9
09-03-15 08:27 PM