RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:
Banzai Racing

Tranny...clutch pedal all the way down and in gear yet it still pulls

Thread Tools
 
Search this Thread
 
Old 10-20-03, 05:11 PM
  #1  
My Bick is Digger

Thread Starter
iTrader: (3)
 
Dltreezan's Avatar
 
Join Date: Oct 2002
Location: Raleigh, NC
Posts: 3,509
Likes: 0
Received 2 Likes on 2 Posts
Tranny...clutch pedal all the way down and in gear yet it still pulls
Ill be sitting at the light with the clutch pedal all the way down with the car in first waiting for the light to change and it starts chattering like its somewhat bouncing off of the flywheel...maybe my release bearing? Just curious....thanx

PS.....it also starts pulling like its actually engaging....I dont think its a hydraulic issue...
Dltreezan is offline  
Reply Like
Old 10-20-03, 06:22 PM
  #2  
Senior Member

 
nopistons's Avatar
 
Join Date: Oct 2001
Location: new jersey
Posts: 691
Likes: 0
Received 0 Likes on 0 Posts
If it's pulling away, it IS engageing. My guess is the clutch master or slave cylinder is leaking internally, allowing the clutch to engage.
nopistons is offline  
Reply Like
Old 10-20-03, 06:30 PM
  #3  
BDC
BDC Motorsports

 
BDC's Avatar
 
Join Date: Jun 2002
Location: Grand Prairie, TX
Posts: 3,667
Likes: 0
Received 6 Likes on 6 Posts
Probably hydraulics like nopistons (aka Vosko?) says.

B
BDC is offline  
Reply Like
Old 10-20-03, 08:01 PM
  #4  
My Bick is Digger

Thread Starter
iTrader: (3)
 
Dltreezan's Avatar
 
Join Date: Oct 2002
Location: Raleigh, NC
Posts: 3,509
Likes: 0
Received 2 Likes on 2 Posts
so it has nothing to do with the throwout bearing or any of that then...has to be hydraulic?
Dltreezan is offline  
Reply Like
Old 10-27-03, 08:28 AM
  #5  
Senior Member

 
nopistons's Avatar
 
Join Date: Oct 2001
Location: new jersey
Posts: 691
Likes: 0
Received 0 Likes on 0 Posts
Correct. (Nope, I'm not Vosko, but I am in NJ, though. Don't have ANYWHERE near as much knowledge about 7's as he does.)
nopistons is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
1993 Massive Hesitation at 2,500 & 5,500 RPMs...
rgordon1979
3rd Generation Specific (1993-2002)
40
03-15-22 12:04 PM
New Greddy Profec Install problem, 12psi on OFF
24seven_dada
3rd Generation Specific (1993-2002)
20
11-10-18 12:03 PM
hogged out vs boost prepped (Nikki)
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
Electrical & Idle problems with 1985 Rx-7 12A
The1Sun
New Member RX-7 Technical
5
09-15-15 04:45 PM
Adaptronic 1280s Hot Start 3 Rotor 20b RX7
Monsterbox
Adaptronic Engine Mgmt - AUS
5
09-11-15 03:29 PM
Tags
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
Where did you guys get your engines?




Advanced Search
Quick Reply: Tranny...clutch pedal all the way down and in gear yet it still pulls


Reply Closed Thread Share

All times are GMT -5. The time now is 06:22 AM.