Spooled Up Racing's Turbo Swap Thread
#177
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
Well ACT's website is wrong.. the flywheel I bought will NOT work on my car so now I am out the time and money in order to get the flywheel and resell it then buy a new one to get the engine installed!!!
this is why I HATE ACT!!!!
this is why I HATE ACT!!!!
#182
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
Screw Racing beat.. I sell Fidanza I will just buy a new fidanza...
I'm using the n/a drive train so the flywheel has to be an N/A flywheel... I bought a turbo ACT flywheel ONLY because ACT website said n/a and T2 are the same..
I hate ACT.. They always seem to be in it for the money and dont give a crap about customer service... I called them talked to the tech guy and his words were...
Even if our catalog is wrong why did u not check with other manufactures to see what they say, before purchasing ours..
My reply..
BECAUSE I BOUGHT YOUR PRODUCT NUMB NUTS!!!!!
CLICK!!!
#189
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
Ok I got my boost sensor on the way to me... bought a new oem release bearing, oem pilot bearing and seal, oem clutch fork and clip and a few gaskets...
I'm getting closer!!!
I'm getting closer!!!
#194
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
I have a turbo trans... I am going to run this setup this season then do the turbo swap next winter...
I have lots of mileage of break in I doubt I will get much time to play with it..
I'll be fine..
BTW tomorrow I order up the stage 3 Spec 6 puk sprung hub clutch
I have lots of mileage of break in I doubt I will get much time to play with it..
I'll be fine..
BTW tomorrow I order up the stage 3 Spec 6 puk sprung hub clutch
#196
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
Its here...
just under 8 lbs...
Today I will be going out to buy some new grade 8 bolts to bolt the flywheel to the counterweight.. Tonight I plan to get this baby torqued down and ready for the clutch...
I cant wait its getting closer!!!
just under 8 lbs...
Today I will be going out to buy some new grade 8 bolts to bolt the flywheel to the counterweight.. Tonight I plan to get this baby torqued down and ready for the clutch...
I cant wait its getting closer!!!
Last edited by SpooledupRacing; 04-04-08 at 07:46 AM.
#199
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
OK today was the day... Unfortunately I could not find any grade 8 metric bolts to bolt the flywheel to the counter weight and my clutch has not arrived yet so I got everything else ready..
First I started but going outside jacking the car up and getting everything disconnected (trans, oil cooler lines, engine mounts etc). RX7Tuner showed up and gave me a hand and after a little coaxing I got him to give me a hand and yank the engine out by hand (My buddy Aaron was gonna be over in about 45 minuted with a cherry picker but I knew we could do it)
Here is what happen before I pulled the engine
Engine is out:
the engine bay
First I started but going outside jacking the car up and getting everything disconnected (trans, oil cooler lines, engine mounts etc). RX7Tuner showed up and gave me a hand and after a little coaxing I got him to give me a hand and yank the engine out by hand (My buddy Aaron was gonna be over in about 45 minuted with a cherry picker but I knew we could do it)
Here is what happen before I pulled the engine
Engine is out:
the engine bay
#200
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
RX7tuner had to take off and about 10 minutes later Aaron shows up.. so
then I decided to pull the clutch off and take a peak since I knew it was toast
We then decided to bring the engine up from the basement and outside...
Imagine the engine bolted to the stand and this is what we had to deal with
Coming up these stairs
then through the hall and down these stairs
then I decided to pull the clutch off and take a peak since I knew it was toast
We then decided to bring the engine up from the basement and outside...
Imagine the engine bolted to the stand and this is what we had to deal with
Coming up these stairs
then through the hall and down these stairs