SpooledupRacing

That will be saweet.. my car wont be running I don't think but I will still be ready for everyone to come..

email me to get info

blwn rtr 89'

iTrader: (5)

will do

SpooledupRacing

Well I just bought some

84-85 13B NT low impedance square top center port 680cc orange 195500-0900 injectors.

I heard they flow like 720cc injector on FC's so these will be my secondary injectors..

I am sending out my other injectors (550cc's) to get them cleaned and flowed so I can use two of them for primarys

RX7Tuner.

Where are you sending them? i have had good experience with cruzin performance in big rapids.

RX7Tuner.

Motor looks awesome! I always loved gunmetal.

SpooledupRacing

I was gonna send them to a place in Wa.. however I will call them tomorrow..

I am happy with the engine painting.. I still need to paint the water pump housing and the front cover..

The Wankler

iTrader: (14)

Looks good!

SpooledupRacing

thank you sir...

The Wankler

iTrader: (14)

You are welcome!

I just rebuilt my block and had a blast doing it. I used new housings though. It starts right up, no problem there with over flooding. It purrs when it revs. I just need to spend some time (remodling the living room) and figure out why i am lean WOT. I will never go anywhere to have my engine rebuilt again.

SpooledupRacing

See thats cool to hear. I like hearing success stories cause then that gives me confidence...

today I bought:
a tube of hylomar (in my posession)

from Pineapple Racing I purchased:
Medium street port template
exhaust port template
S4 T2 omp block off plate
S4 T2 air control valve block off plate
crank sensor cover plate (with ninja )
omp injector block off plugs


so I should see those before the weekend...

I cant wait I get to start porting here very soon.. I am so siked!!!

The Wankler

iTrader: (14)

I had to port the housings. That was a piece of cake. The irons looked a bit more difficult but they had been done by Atkins. That hylomar can get real fking messy.

SpooledupRacing

yeah I was gonna just use crisco but I decided to buy the hylomar at the time..

do u happen to have any pic of your ported housings (that u did)

Alex Rodriguez

iTrader: (137)

looking good bro keep it up

SpooledupRacing

thank you sir

The Wankler

iTrader: (14)

You bet, here you go! And one of my engine complete.

texFCturboII

iTrader: (17)

ooooohhhhhh.......pretty.......

SpooledupRacing

ok show off

enough of your preaty **** in my thread lol....

very nice ****...

The Wankler

iTrader: (14)

I was just showing you the Brake & Clutch masters I bought from ya,,,,,,,, INSTALLED!

LOLOLOL..... yeah, I have been to lazy to start a thread this time.

Throwing you a little inspiration my friend.
Chris

SpooledupRacing

THX man it is definitely inspiration..

btw I love the master cylinders very nice looking

stylEmon

iTrader: (2)

did you get the injectors you needed?

SpooledupRacing

I bought the injectors I need yes.. I just am waiting for them to show up and waiting to send out my 550's

SpooledupRacing

Well while I await my pats to show up I have cleaned up the work bench down stairs and I am going to pull all of the parts on it ...

Yes Brian this is where the porting will take place lol..

I will update with any more info or pics as things change

The Wankler

iTrader: (14)

The walls have the look of, "Snuff Flick Room Walls"..... :0) Natural stone or plaster?

You got plenty of room!

AlexG13B

iTrader: (7)

"this is where the fun takes place" :p

SpooledupRacing

Michigan basement.. I have rock and sand with a little plaster on the walls..

quite rustic.