solid information...everything is jumbled up and nothign is clear.
Thread Starter
Using no way as way
Joined: Jan 2005
Posts: 104
Likes: 0
From: Georgia
solid information...everything is jumbled up and nothign is clear.
I just want some solid info. I have been searching and searching and each time someone says this and another says this. I want some solid information in this thread please. Do i need to get engine mounts to put my 87 turbo ii into my 90 gxl? Will the tranny, driveshaft, and diff in my 90 gxl work? Do i need to have a 90 turbo ii flywheel or can I use the one from my 87 turbo ii? There are a lot more questions but these are the ones I really want answer to because they determine if my swap works or not. Thank you greatly.
Brandon
Brandon
Mountain Rotary Mod
Joined: Nov 2003
Posts: 2,411
Likes: 0
From: Freaking Poland!!
You didn't search very well. This is covered near daily on this forum.
The T2 engine will bolt directly in.
the NA tranny and drivetrain will work ONLY if you change the T2 flywheel to NA.
The T2 tranny does not match the NA drive train, all of it will need to be replaced (including the rear diff) if you intend to use the T2 tranny.
go to http://www.rotaryresurrection.com and search his tech info.
The T2 engine will bolt directly in.
the NA tranny and drivetrain will work ONLY if you change the T2 flywheel to NA.
The T2 tranny does not match the NA drive train, all of it will need to be replaced (including the rear diff) if you intend to use the T2 tranny.
go to http://www.rotaryresurrection.com and search his tech info.
Joined: Dec 2001
Posts: 10,630
Likes: 3
From: NY, MA, MI, OR, TX, and now LA or AZ!
WHY do people continuelly put the WRONG series engine in their cars? This makes installation SO much harder. You're either going to have to hack your wiring up, or swap damn near every part on the motor and use a s5 TII ECU/pressure sensor/AFM/etc. Why!?
HAILERS
Joined: May 2001
Posts: 20,563
Likes: 27
From: FORT WORTH, TEXAS,USA
You should put your turboii engine AND transmission in the car. It wasn't clear that you were putting in the trubo transmission or not. You need a trubo transmission brace to do that. The na brace/mount won't work.
If you use the n/a transmission and the turbo engine you need to change the flywheel and the front engine counterweight.
If you put a turbo transmission in, and leave the n/a rear, then you need a hybrid drive shaft made or bought from MAZDATRIX.
The n/a afm will werk but you need the turbo pressue sensor.
You need a turbo ECU.
If you use the turbo engine but want to keep the ninty transmission then you have to do what was said above and change flywheels AND front counterweight. I think I said that already...
I could make the ninty wiring harness work easily. But that's me......not you. A lot depends on skill level (i.e. hung around the car a lot and READ the schematics).
If you use the n/a transmission and the turbo engine you need to change the flywheel and the front engine counterweight.
If you put a turbo transmission in, and leave the n/a rear, then you need a hybrid drive shaft made or bought from MAZDATRIX.
The n/a afm will werk but you need the turbo pressue sensor.
You need a turbo ECU.
If you use the turbo engine but want to keep the ninty transmission then you have to do what was said above and change flywheels AND front counterweight. I think I said that already...
I could make the ninty wiring harness work easily. But that's me......not you. A lot depends on skill level (i.e. hung around the car a lot and READ the schematics).
Thread
Thread Starter
Forum
Replies
Last Post
Captain Hook
2nd Generation Specific (1986-1992)
13
Oct 4, 2015 06:35 PM
FührerTüner
2nd Generation Specific (1986-1992)
13
Sep 27, 2015 02:16 PM
