Rummble Rummble Blap blap!
#1
Damnit, steel doors hurt!
Thread Starter
Join Date: Apr 2003
Location: Charlotte, NC
Posts: 788
Likes: 0
Received 0 Likes
on
0 Posts
Rummble Rummble Blap blap!
Ok well after my car passed emissions today I came home today and welded up me an exhaust, not completly finished as I'm to tired to finish it, you will see in picture. But I welded on a 2.5" pipe from the header to a muffler and then 2.5" pipe out the passenger side. I wanted to do it on the driver side but since the brake lines and other lines run on that side it went on the passenger side.
Well heres the pic, remmebr not finished, it needs about a foot cut off the pipe. Tell me what you think, i will try to get up new pics tomorow when its finished and a sound clip also.
Well heres the pic, remmebr not finished, it needs about a foot cut off the pipe. Tell me what you think, i will try to get up new pics tomorow when its finished and a sound clip also.
#5
Damnit, steel doors hurt!
Thread Starter
Join Date: Apr 2003
Location: Charlotte, NC
Posts: 788
Likes: 0
Received 0 Likes
on
0 Posts
I guess you could go out on the driver side but there will be brake lines and gas lines right above the pipe, which i don't think is a good idea.
Trending Topics
#10
Damnit, steel doors hurt!
Thread Starter
Join Date: Apr 2003
Location: Charlotte, NC
Posts: 788
Likes: 0
Received 0 Likes
on
0 Posts
Ok here some finished pics, i think I'm going to get a tip or something for it I'm not sure, i painted it flat black not to make it so obvious.
#11
Full Member
Join Date: Sep 2001
Location: Ft lauderdale
Posts: 71
Likes: 0
Received 0 Likes
on
0 Posts
Awesome. Your going scare the hell out of people next to you in traffic when you start Ripping Flames out that thing.I wanted to dump my downpipe right behind the front wheel. But i dont wanna sacrafice my paint job,my rear is charr broiled as it is.
#12
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,827
Received 2,595 Likes
on
1,843 Posts
Gangsta! You should oval it, even more ruthless.
#14
Damnit, steel doors hurt!
Thread Starter
Join Date: Apr 2003
Location: Charlotte, NC
Posts: 788
Likes: 0
Received 0 Likes
on
0 Posts
Ok well no flamage, yet?!
What will make it shoot flames?
As of now my mods are:
Ported and polished throttle body with cold start removed
2.5" header back exhaust(as seen above)
Cone filter
Power sterring, AC, and Air pump removed
Centerforce Dual Friction clutch
I got a few more emission things to remove. Also I want to redo the vacum lines as I'm sure ther is probally a cracked one some where in there.
What will make it shoot flames?
As of now my mods are:
Ported and polished throttle body with cold start removed
2.5" header back exhaust(as seen above)
Cone filter
Power sterring, AC, and Air pump removed
Centerforce Dual Friction clutch
I got a few more emission things to remove. Also I want to redo the vacum lines as I'm sure ther is probally a cracked one some where in there.
#22
Damnit, steel doors hurt!
Thread Starter
Join Date: Apr 2003
Location: Charlotte, NC
Posts: 788
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
bladekill
1st Generation Specific (1979-1985)
1
07-18-04 09:30 PM