need help with intsall afc neo
#1
boosted fc
Thread Starter
iTrader: (3)
Join Date: Dec 2007
Location: texas
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
need help with intsall afc neo
its an 89 gxl i dont kow what to set the hot wire pessure and flap at?
i left them at 1-1 and every time you touch the throttle it dies need help please
i left them at 1-1 and every time you touch the throttle it dies need help please
#3
boosted fc
Thread Starter
iTrader: (3)
Join Date: Dec 2007
Location: texas
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
you cant set it at 00
i have them all at 1-1 and evey time you tap the throttle it dies
or does anyone else have a better way to explain how to set it up, the instructions suck
i have them all at 1-1 and evey time you tap the throttle it dies
or does anyone else have a better way to explain how to set it up, the instructions suck
#5
boosted fc
Thread Starter
iTrader: (3)
Join Date: Dec 2007
Location: texas
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
i got it set t set with 4 cyl. and poitiig to the upper right, it is an s5
ok so i set the flap at 06-06
now what about hot wire and prssure
and should it hav lik a base map or do i have to retune the air and fuel
the instructions dont explain anything
ok so i set the flap at 06-06
now what about hot wire and prssure
and should it hav lik a base map or do i have to retune the air and fuel
the instructions dont explain anything
#6
Full Member
iTrader: (2)
Join Date: Feb 2008
Location: Dallas
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
Is your wiring correct? It sounds like you mis-wired the the two air lines. I did that the first time I installed my neo. Recheck your wiring. The settings arent like the S-Afc, leave it at 1-1 from there you can adjust your fuel, but check you wiring first.
Trending Topics
#15
boosted fc
Thread Starter
iTrader: (3)
Join Date: Dec 2007
Location: texas
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
ok i put the flap at 6-6 and the others at 1-1
it runs better other than the idle is searching until full throttle then it sounds like it dies and the picks back up at like 1500 rpm and revs to 2500 rpm and it does same thing
and my wiring is exacley how it says to do it for hotwire, pressure, and flap
any one have any ideas need help asap thanks
oh yeah and it says to do intialsetup before you start the engine everytime i hit yes it restarts and i have to re put in all the infromation
it runs better other than the idle is searching until full throttle then it sounds like it dies and the picks back up at like 1500 rpm and revs to 2500 rpm and it does same thing
and my wiring is exacley how it says to do it for hotwire, pressure, and flap
any one have any ideas need help asap thanks
oh yeah and it says to do intialsetup before you start the engine everytime i hit yes it restarts and i have to re put in all the infromation
#19
boosted fc
Thread Starter
iTrader: (3)
Join Date: Dec 2007
Location: texas
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
i havent done anything im not sure where to start i have all the ect. settings done other than that i dont have anything
where do i need to put the throttle and air map i want it like the stock map for now
where do i need to put the throttle and air map i want it like the stock map for now
#20
Rotary Enthusiast
iTrader: (1)
Three quick questions:
1) Was the car running fine before you installed the Neo?
After you do the setup with the car keyed to on but not running...
2) if you go to - as I recall - "display" mode and work the throttle pedal do you see the value changing for the throttle? What does it say at no pedal and then to the floor?
3) have a friend move the flap inside the AFM. What values do you see at both ends of the range?
1) Was the car running fine before you installed the Neo?
After you do the setup with the car keyed to on but not running...
2) if you go to - as I recall - "display" mode and work the throttle pedal do you see the value changing for the throttle? What does it say at no pedal and then to the floor?
3) have a friend move the flap inside the AFM. What values do you see at both ends of the range?
#22
My RX7 doesn't run yet!!
Join Date: Oct 2009
Location: Tucson
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
09-16-15 09:07 PM
rx8volks
Canadian Forum
0
09-01-15 11:02 PM