Fd adapter
#3
Full Member
Check these threads out.. Good Luck!
https://www.rx7club.com/2nd-gen-gene...ystem-1110841/
https://www.rx7club.com/2nd-generati...1098928/page6/
https://www.rx7club.com/2nd-gen-gene...ystem-1110841/
https://www.rx7club.com/2nd-generati...1098928/page6/
#4
rotorhole
i dont think elite sells them anymore, probably realized how poor the FC market still is. least not listed on their website anymore so any information is gone now.
#5
Full Member
If you're still alive OP I did come across this.
MAZDA(FC3S) | ????? | ??????????????????????????????????????????
Page 3 RE Action Racing offers a FC to FD UIM adapter. I have no clue if it adapts the S4 or S5 LIM to the s6 UIM though so you would need to make sure on that one.
MAZDA(FC3S) | ????? | ??????????????????????????????????????????
Page 3 RE Action Racing offers a FC to FD UIM adapter. I have no clue if it adapts the S4 or S5 LIM to the s6 UIM though so you would need to make sure on that one.
#6
Full Member
Came across an older thread here with a guy that got the Re Action Racing manifold adapter (listed in my post above) from a parts importer in Japan https://www.rx7club.com/2nd-generati.../#post11979881
I contacted the same parts importer and promptly got a response from them saying they will follow up with it on Monday when Re Action Racing is open.
I'll update whatever I find for people that might have a similar interest in converting to a FD UIM since this might be the only current maker of the adapter.
I contacted the same parts importer and promptly got a response from them saying they will follow up with it on Monday when Re Action Racing is open.
I'll update whatever I find for people that might have a similar interest in converting to a FD UIM since this might be the only current maker of the adapter.
Trending Topics
#10
Full Member
Just got a reply so as promised here's what I've been told copy pasted below. No idea if this Re Action Racing part is a s4 to s6 adapter or s5 to s6 adapter, I'll ask for clarification. Looking at around 400 bucks total. Once again I contacted this person through About Streeter Corporation (post 6 in this thread)
Re Action Racing Conversion Adapter for Surge Tank FC3S - 30110yen+1080yen domestic shipping, will take 3-4 days
Re Action Racing Conversion Adapter for Surge Tank FC3S - 30110yen+1080yen domestic shipping, will take 3-4 days
landed would look like this...
Cost of item(s):¥30,110
Ship item(s) from seller to Streeter Corp:¥1,080
Bank fee:¥630My commission:¥3,000
Subtotal:¥34,820
Shipping options available to USA:
EMS option (4-6 days *does not include shipping time to me)
Shipping cost (estimated 3 kg):
¥5,900* (I could be off with the weight but what ever it costs to send Ill pass on to you)
Rough total cost (subtotal + shipping) via EMS in JPY:¥40,720
Rough total cost if paid by Paypal:¥42,348
Rough total cost if paid by Paypal in USD at approximate Paypal rate of 102.0 $415
* PLEASE DO NOT MAKE PAYMENT YET!!
THIS IS JUST A ROUGH ESTIMATE, SO PLEASE DO NOT PAY THE ROUGH QUOTE AMOUNT!!
Rough shipping quote
Cost of item(s):¥30,110
Ship item(s) from seller to Streeter Corp:¥1,080
Bank fee:¥630My commission:¥3,000
Subtotal:¥34,820
Shipping options available to USA:
EMS option (4-6 days *does not include shipping time to me)
Shipping cost (estimated 3 kg):
¥5,900* (I could be off with the weight but what ever it costs to send Ill pass on to you)
Rough total cost (subtotal + shipping) via EMS in JPY:¥40,720
Rough total cost if paid by Paypal:¥42,348
Rough total cost if paid by Paypal in USD at approximate Paypal rate of 102.0 $415
* PLEASE DO NOT MAKE PAYMENT YET!!
THIS IS JUST A ROUGH ESTIMATE, SO PLEASE DO NOT PAY THE ROUGH QUOTE AMOUNT!!
Last edited by Mlammert; 03-07-18 at 07:14 AM.
#11
Full Member
Got the reply about series specification.
"apparently the adapter is for kouki FC only, they dont do one for the zenki." -Streeter Corp
So series 5 only for the Re Action Racing adapter.
"apparently the adapter is for kouki FC only, they dont do one for the zenki." -Streeter Corp
So series 5 only for the Re Action Racing adapter.
#15
Senior Member
To do it right you have to also fill weld the inner ports on the FD upper manifold on one side about an 1 inch or so up into the port, then port match to the FC gasket.... otherwise the port doesn't stay the same diameter. the outer bolt holes don't line up either on the FD upper....it's bit of work this way but you are not adding any length to the intake track that using an adaptor adds.
Last edited by Nosferatu; 03-10-18 at 03:27 PM.
#16
FC guy
iTrader: (8)
To do it right you have to also fill weld the inner ports on the FD upper manifold on one side about an 1 inch or so up into the port, then port match to the FC gasket.... otherwise the port doesn't stay the same diameter. the outer bolt holes don't line up either on the FD upper....it's bit of work this way but you are not adding any length to the intake track that using an adaptor adds.
we port matched mine 5 years ago, still running it. only one bolt was really an issue and it wasnt even that much of an issue.
if someone doesnt port they can have it done probably for a buck, buck and a half.
what i think would be a good idea is a very thin metal spacer to go between the UIM/LIM to sandwhich a s5/s6 gaskets, and i still may do it just need to talk to my local guy
#17
Full Member
Here's another source than Re Action Racing.
https://www.billetrotary.com.au/prod...ld-hat-adaptor
Doesn't look like they offer an option for specifically s4 or s5 LIM so I'm curious how close it would match up given s4 and s5 LIM have different ports. It is quite a bit cheaper though.
https://www.billetrotary.com.au/prod...ld-hat-adaptor
Doesn't look like they offer an option for specifically s4 or s5 LIM so I'm curious how close it would match up given s4 and s5 LIM have different ports. It is quite a bit cheaper though.
#18
www.AusRotary.com
Here's another source than Re Action Racing.
https://www.billetrotary.com.au/prod...ld-hat-adaptor
Doesn't look like they offer an option for specifically s4 or s5 LIM so I'm curious how close it would match up given s4 and s5 LIM have different ports. It is quite a bit cheaper though.
https://www.billetrotary.com.au/prod...ld-hat-adaptor
Doesn't look like they offer an option for specifically s4 or s5 LIM so I'm curious how close it would match up given s4 and s5 LIM have different ports. It is quite a bit cheaper though.
PS I was the one referred to above who got the REaction Racing one from Japan through an Australian sales agent. I can confirm it is to suit the s5 LIM. I never ended up using it and sold it locally. I was never really happy with the look of an adapter plate. It's all so...obvious.
I'm actually considering cutting the flange off a FD LIM and welding it to a s5 LIM, then port matching with a die grinder. I'm confident the end result will look much neater.
#19
Full Member
I know someone who specifically asked them which series LIM it suits and they didn't have a clue. Not exactly promising. It is going to fit one of them so it's still a good 50% chance you'll get the right one! I'm considering taking a chance if they offer a refund if not suitable. Of course, I'm local so don't have to risk big shipping costs and delay.
PS I was the one referred to above who got the REaction Racing one from Japan through an Australian sales agent. I can confirm it is to suit the s5 LIM. I never ended up using it and sold it locally. I was never really happy with the look of an adapter plate. It's all so...obvious.
I'm actually considering cutting the flange off a FD LIM and welding it to a s5 LIM, then port matching with a die grinder. I'm confident the end result will look much neater.
PS I was the one referred to above who got the REaction Racing one from Japan through an Australian sales agent. I can confirm it is to suit the s5 LIM. I never ended up using it and sold it locally. I was never really happy with the look of an adapter plate. It's all so...obvious.
I'm actually considering cutting the flange off a FD LIM and welding it to a s5 LIM, then port matching with a die grinder. I'm confident the end result will look much neater.
#21
www.AusRotary.com
http://www.ausrotary.com/viewtopic.php?f=4&t=246728
As you can see, it's very well made and quite thick. The thickness is probably a good thing in that it will help with clearance under the UIM, but it is very very conspicuous. I reached the conclusion that a hunk of billet sandwiched between the manifolds doesn't actually look nice (even the adapter itself looks great).
Last edited by KYPREO; 04-03-18 at 09:46 PM.
#23
Full Member
Hi. There's some pics of the Reaction Racing 13B-REW UIM to s5 LIM adapter here:
fitting fd upper intake to fc 13b - AusRotary
As you can see, it's very well made and quite thick. The thickness is probably a good thing in that it will help with clearance under the UIM, but it is very very conspicuous. I reached the conclusion that a hunk of billet sandwiched between the manifolds doesn't actually look nice (even the adapter itself looks great).
fitting fd upper intake to fc 13b - AusRotary
As you can see, it's very well made and quite thick. The thickness is probably a good thing in that it will help with clearance under the UIM, but it is very very conspicuous. I reached the conclusion that a hunk of billet sandwiched between the manifolds doesn't actually look nice (even the adapter itself looks great).
The following users liked this post:
Mlammert (04-05-18)
#25
Full Member
Yeah I see it now, nice big pictures too. Well the machining, finish and construction seem to all be pretty solid on it. Might have to pick one up while they're still making them for the parts hoard. Pretty commendable for a little shop to still be selling them 16 years later. Thanks for sharing the pictures.
Last edited by Mlammert; 04-05-18 at 03:44 AM.
Thread
Thread Starter
Forum
Replies
Last Post
StellarZ
Interior / Exterior / Audio
5
10-04-10 05:10 PM
t_mak@mail.plymouth.edu
Interior / Exterior / Audio
1
08-12-01 10:26 PM