Erorr code checker lamp, key on, not blinking.
05-20-06, 06:00 PM
#2
I'm a boost creep...
Join Date: Jan 2002
Location: Auckland, New Zealand
Posts: 15,608
Likes: 0
Received 8 Likes
on
8 Posts
There should be two LED's (you imply just one) and they should light up for three seconds when you turn the ignition on. If they don't you probably have it hooked up wrong.
05-20-06, 06:17 PM
#3
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes
on
19 Posts
If you have two led's then the common wire b/t them should go the BLACK/WHITE wire in the six socket, green check connector. The other two go in the two sockets on the left of the black/white.
Like the NZ said, key to ON, the lights come on for about three secconds the goat out. Now if the key is still on, and you pull the elec plug off the boost sensor, you should get a blinking light/lights. I'd warm the engine up first just to make sure the tps is where it should be. This step is probably superstition. Can't hurt.
Like the NZ said, key to ON, the lights come on for about three secconds the goat out. Now if the key is still on, and you pull the elec plug off the boost sensor, you should get a blinking light/lights. I'd warm the engine up first just to make sure the tps is where it should be. This step is probably superstition. Can't hurt.
05-20-06, 06:28 PM
#5
I screwed up, it works fine. Sorry about that.
Anyhow, I am looking into the injectors as you mentioned Hailers, for my lean problem. Going to test the flow and do the oam checks on it.
I did do the fuel pump relay mod, is it possible I wired something backwards cause me to run lean?
.
Anyhow, I am looking into the injectors as you mentioned Hailers, for my lean problem. Going to test the flow and do the oam checks on it.
I did do the fuel pump relay mod, is it possible I wired something backwards cause me to run lean?
.
05-20-06, 06:50 PM
#6
I'm a boost creep...
Join Date: Jan 2002
Location: Auckland, New Zealand
Posts: 15,608
Likes: 0
Received 8 Likes
on
8 Posts
Originally Posted by 88rxn/a
i read this on fc3s but i didnt see where it shows what the blinks mean?
http://www.teamfc3s.org/info/article...odes/main.html
05-20-06, 06:55 PM
#7
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
guess i didnt.....thanks
Originally Posted by NZConvertible
You obviously didn't read the whole page then...
http://www.teamfc3s.org/info/article...odes/main.html
http://www.teamfc3s.org/info/article...odes/main.html
Trending Topics
05-25-06, 04:08 PM
#8
tom port.. AKA streetport
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
http://www.radioshack.com/product/in...9&tab=features
these are what i got yesterday....
apparently im not hooking them up right either...i tried today and got no lights to come on..i guess ill go and try again...
edit: these have the built in resistors also
these are what i got yesterday....
apparently im not hooking them up right either...i tried today and got no lights to come on..i guess ill go and try again...
edit: these have the built in resistors also
08-07-06, 04:03 AM
#12
I'm a boost creep...
Join Date: Jan 2002
Location: Auckland, New Zealand
Posts: 15,608
Likes: 0
Received 8 Likes
on
8 Posts
Originally Posted by MrFC3S
i put it in the wrong way the first time, would that possiably mess up anything?
Thread
Thread Starter
Forum
Replies
Last Post
