Infini 4 seat prices?
#1
Banned. I got OWNED!!!
Thread Starter
iTrader: (2)
Join Date: Mar 2011
Location: Parksville, BC
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
Infini 4 seat prices?
So I picked up a Infini 4 mazdaspeed seat, apparently the last 20 infinis came with them and I was curious what something like this would sell for? Its the passenger seat (driver's side here in north america) which I was intending to use but may need to end up selling it but I can not find one that was sold here and have no idea what they are going for!
#2
Rotary Enthusiast
iTrader: (1)
Join Date: Nov 2012
Location: bloomington, mn
Posts: 1,100
Likes: 0
Received 0 Likes
on
0 Posts
https://www.rx7club.com/2nd-generati...-seats-388182/
$420 ebay, apparently it's is same as infini 3 seat as well.
that took all of 20 seconds to hunt down... smh
$420 ebay, apparently it's is same as infini 3 seat as well.
that took all of 20 seconds to hunt down... smh
#3
Banned. I got OWNED!!!
Thread Starter
iTrader: (2)
Join Date: Mar 2011
Location: Parksville, BC
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
I know the 3 and 4 look the same, except this one is all black and well 1 of 20. The infini 4 seats as well are more rare. Also going from that thread they sold for 420 as they were in very bad condition and that was back in 2005, not very current. I've already googled these things and could not find this particular seat being sold on the forum. That's why I asked.
Trending Topics
#10
bravebluerx
iTrader: (4)
Tilt adjusting Infini 3 seats
The infini 3 seats have the tilt adjustment mechanisms built into the seat, but an exterior adjustment lever is not welded to the adjustment arm like the infini 4 seats are. You could add your own exterior adjustment tilt bar to the infini 3 seat if you can get enough room in the slot to tack a short weld and add/bend your own little exterior adjustment bar.
Without welding your own tilt adjustment bar you can still utilize the tilt adjustment mechanism before you mount the infini 3 seat in your car by pulling up on the lever that has the open "u" slot arm (below the spring) in the attached picture with pliers or using a screw driver shaft while sitting in the seat and tilting the seat back-back and then releasing the attachment to lock that position. It will fix the seat back at a slight recline, which I did and like.
Without welding your own tilt adjustment bar you can still utilize the tilt adjustment mechanism before you mount the infini 3 seat in your car by pulling up on the lever that has the open "u" slot arm (below the spring) in the attached picture with pliers or using a screw driver shaft while sitting in the seat and tilting the seat back-back and then releasing the attachment to lock that position. It will fix the seat back at a slight recline, which I did and like.
#13
Banned. I got OWNED!!!
Thread Starter
iTrader: (2)
Join Date: Mar 2011
Location: Parksville, BC
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
I did not spend as much as you would think :P, I bought it out of japan so it being a passenger seat with no matching driver one so it's not very desirable over there. I see regular infini 3-4 seats sometimes go for 50-100 a seat.
#14
★*NGTDRV★*
iTrader: (16)
Sorry, I looked at the pictures really quick and thought they were form an ebay listing (thought I saw the little camera logo in the corner and everything lol)
....I think they are worth what you paid and I am willing to give you twice as much! lol
Good luck figuring it out!
....I think they are worth what you paid and I am willing to give you twice as much! lol
Good luck figuring it out!
Thread
Thread Starter
Forum
Replies
Last Post