1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

Runing issue

Thread Tools
 
Search this Thread
 
Old 01-17-24, 09:53 PM
  #1  
Newbie
Thread Starter
 
Mrmikeb1999's Avatar
 
Join Date: Dec 2023
Location: Ohio
Posts: 2
Received 0 Likes on 0 Posts
Runing issue

Last year i bought a 1980 rx 7 and it ran great. But recently it died on my way to work. It has new fule filter spark plugs battery and alternator. I can get it to start and idle but after a min or 2 it dies and won't start again. Any suggestions on what could be wrong.
Old 01-18-24, 04:40 AM
  #2  
Rotary Freak

 
WJM ROTARIES's Avatar
 
Join Date: Aug 2012
Location: MELBOURNE AUSTRALIA
Posts: 2,411
Received 307 Likes on 299 Posts
Welcome to forum .It sounds like your fuel pump has died and you need a new one
Old 01-18-24, 10:11 AM
  #3  
Damn, it did start!

 
Richard Miller's Avatar
 
Join Date: Feb 2001
Location: washington
Posts: 2,678
Received 365 Likes on 226 Posts
A consideration is parts house parts generally don’t last as long as oem. For the fuel pump , it’s easy to change out. I’m going from memory here but a lot of carburetor rated pumps run higher pressure than the Mazda carburetor wants to see. I think for the Mazda it’s 1.5psi. But I’m going from fuzzy memory. So illl happily be corrected.
The following users liked this post:
Mrmikeb1999 (01-21-24)
Old 01-18-24, 10:50 AM
  #4  
Happy Rotoring!

iTrader: (13)
 
Banzai's Avatar
 
Join Date: Dec 2007
Location: Iowa
Posts: 2,305
Received 378 Likes on 247 Posts
Checking the fuel pump is a good place to start, but I'd think that either the pump works or it doesn't. Working for a minute or two then not working but functioning again later isn't a common fault for a pump. Have you ever had a look inside the fuel tank? Rust, gunk and debris can build up over time and settle in the bottom. When you start the car and the pump draws fuel from the tank, loose crud can be sucked up and collect around the fuel sock and choke off the flow. After it shuts off, the draw is gone and the debris fall back away.
The following 2 users liked this post by Banzai:
KansasCityREPU (01-18-24), Mrmikeb1999 (01-21-24)
Old 01-18-24, 02:34 PM
  #5  
Out In the Barn


iTrader: (9)
 
KansasCityREPU's Avatar
 
Join Date: Mar 2005
Location: KC
Posts: 6,055
Received 1,015 Likes on 801 Posts
Also, since it's a 40+ year old car, the fuel soft lines aren't so shot any longer. all the the fuel soft lines should be replace from the tank to carb. They are 6mm and 8mm.
The following users liked this post:
Mrmikeb1999 (01-21-24)
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gainer_reniag
3rd Generation Specific (1993-2002)
12
01-10-07 10:21 PM
Keisuke Takahashi
2nd Generation Specific (1986-1992)
2
12-03-06 01:17 PM
RevZempoe
3rd Generation Specific (1993-2002)
10
04-07-05 06:15 PM
chexmix78
2nd Generation Specific (1986-1992)
7
07-27-04 03:26 PM
rybrx7
3rd Generation Specific (1993-2002)
10
01-13-04 11:08 PM



Quick Reply: Runing issue



All times are GMT -5. The time now is 10:26 AM.