no power to ecu, coils
#1
Royale with cheese
Thread Starter
Join Date: Jan 2004
Location: Las Vegas, by way of Poulsbo, WA
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
no power to ecu, coils
So, my -SE just randomly died. with the key on, I get brake and coolant dummy lights, no oil p. or alt. It cranks just fine. However, it doesn't get spark, and the injectors don't fire. Im getting fuel to the rail. Im getting power to and through all the fusibles. No blown fuses. Not getting power to either of the ECU connectors. Can't find any bad grounds. What am I missing?
#4
Old Fart Young at Heart
iTrader: (6)
How are you checking the fusible links? If you connect a test meter from terminal to terminal, all that does is complete the circuit and bypasses the link Link needs to be unplugged and tested from the unplugged end to the terminal. If those are good, prop open the flap in the MAF and see if that makes a difference.
Are you getting a tach signal during cranking? If not there may be a bad wire or the trailing ignitor is toast.
Are you getting a tach signal during cranking? If not there may be a bad wire or the trailing ignitor is toast.
#5
Royale with cheese
Thread Starter
Join Date: Jan 2004
Location: Las Vegas, by way of Poulsbo, WA
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
Checking them to ground, both sides. I get 12v everywhere. Does the trailing ignitor give signal to the eco to fire fuel and spark? Ill try the flapper door.
And still for some reason, no power to + side of coil with key on. That would tell me ignition relay, only it cranks.
the trailing ignitor probably is bad. About 2 weeks after I bought it, after Id been driving it the whole time, I noticed that the T ignitor was unplugged, and had been the whole time. WHen I plugged it back in, it made no difference in how the car ran or idled.
And still for some reason, no power to + side of coil with key on. That would tell me ignition relay, only it cranks.
the trailing ignitor probably is bad. About 2 weeks after I bought it, after Id been driving it the whole time, I noticed that the T ignitor was unplugged, and had been the whole time. WHen I plugged it back in, it made no difference in how the car ran or idled.
#6
Old Fart Young at Heart
iTrader: (6)
The trailing does very little for power, 2-3% at most. It's main purpose is to clean up emissions. The tach is fed from the trailing coil. If the trailing ignitor goes out, the engine won't start, it will crank though. Maybe the PO changed some of the wiring around. Time to download the wiring manual and start checking.
#7
Royale with cheese
Thread Starter
Join Date: Jan 2004
Location: Las Vegas, by way of Poulsbo, WA
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
Sigh... I know. I'm really not looking forward to it. Goddammit, why can't someone just know exactly what is wrong and tell me how to fix it?! You're all useless!!
Trending Topics
#9
Royale with cheese
Thread Starter
Join Date: Jan 2004
Location: Las Vegas, by way of Poulsbo, WA
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
A little update.
Swapped out the ECU, ignition switch, both main relays, and the ignitors. Still, no power to the coils or ecu. So I broke out the wiring diagram, and started checking everything. The main relays control pretty much everything in the ECU power department. The relays are getting power to them, have ground. They get they're signal directly from the ignition switch., through a 20A fuse inside. Heres where it gets wierd.
With the ignition switch OFF, I get continuity between the ig. switch, and the relays, but its about 30 ohms. With the switch in the ON position, no continuity. If I jumper the "switch" terminal on the relay to the battery, BAM, power everywhere. So the relay isn't getting told to close. Could it be TWO bad ignition switches? The wire in question is the BW coming off the back of the switch. Goes from there to the fuse block, from fuse block to relays.
Im hoping someone could take a look at the diagram for me, double check what Im looking at. Feels like Im missing something stupid here.
Thanks
Swapped out the ECU, ignition switch, both main relays, and the ignitors. Still, no power to the coils or ecu. So I broke out the wiring diagram, and started checking everything. The main relays control pretty much everything in the ECU power department. The relays are getting power to them, have ground. They get they're signal directly from the ignition switch., through a 20A fuse inside. Heres where it gets wierd.
With the ignition switch OFF, I get continuity between the ig. switch, and the relays, but its about 30 ohms. With the switch in the ON position, no continuity. If I jumper the "switch" terminal on the relay to the battery, BAM, power everywhere. So the relay isn't getting told to close. Could it be TWO bad ignition switches? The wire in question is the BW coming off the back of the switch. Goes from there to the fuse block, from fuse block to relays.
Im hoping someone could take a look at the diagram for me, double check what Im looking at. Feels like Im missing something stupid here.
Thanks
#10
Out In the Barn
iTrader: (9)
Sound like a bad wire to me. Is there any way you can expose the wire a both ends and put a jumper between them? What page in FSM wiring diagram are you using? I'll take a look at it also. I know my Navy Electronics Technician training would come in handy. Of course it's been 20 years since I got out.
Thread
Thread Starter
Forum
Replies
Last Post
Skeese
Adaptronic Engine Mgmt - AUS
65
03-28-17 03:30 PM
The Shaolin
2nd Generation Specific (1986-1992)
9
09-14-15 07:50 PM
stickmantijuana
MoTeC
5
09-10-15 07:58 PM