bad 83

iTrader: (3)

Well, I was on my way to work this morning driving my SA. Just a typical morning like every day. Got up at 4:45 am to get ready for work. Went out and fired up the SA at 5:15 am. Let her warm up a little like I always do before I head out. Left for work at 5:30. I got about halway to work when the engine started lumping like a dead miss. No warnings, just started shaking. 5:45 am, turned around and headed back home limping. I pulled in the driveway at almost 6:00 am. I knew what had happened. So I said "screw it", and started pulling the engine. I wasn't going to make to work on time anyway, so the engine was coming out TODAY. I finished about 7:45 am. Not too bad. About 1 1/2 hours from running hot engine, to out sitting on the lift. Well damn. Turned the engine over while looking in the exhaust ports, and guess what? Just as I thought. There was an Apex seal out off the rear rotor. Looks like it gouged thinks up pretty good on it's swift exit. I decided to take a couple pics, so with that being said.........









And of course the "missing" Apex seal.




You got a hate it when that happens.........

gsl-se addict

iTrader: (3)

That sucks, Sam. I have a spare rotor from my old SA that you could have, but it is a front one. I lost the rear apex on my old SA too. Pretty sure I have a spare 12A housing too, but I think that it has too much chrome flake to be worth using.

bad 83

iTrader: (3)

Thanks Kent. It sucks the big one, but I brought her back from the dead once before, and I will again. I can't bitch too much. I paid $150 for the engine and trans, and I put almost 10k miles and almost 9 months on her. I guess I'll try to hit Stu up on one of those many 12As he has lying around (hint hint) . We can rebuild her.......We can make her stronger......Faster........

ray green

iTrader: (14)

A blown apex seal could not have happened in better hands. Nice recovery Sam!

yetterben

WTF that blows but like yah said you got yah monies worth from her

bad 83

iTrader: (3)

I just hate that I have using her for my DD to work. I guess I'll have to blow the dust off the Beemer and drive her till I get a new organ for the SA. I loved the early morning romps to work. I usually pass the same clown almost every day in his widebody Eclipse. He stopped me at work one day and asked if that 280 had a straight six in it. I laughed when I told him that his Eclipse had been getting its doors blown off every day by a 1.1L Rotary . He didn't seem very amused.......

Rx72Heaven

iTrader: (2)

how manny KM or miles on it? a NA engine should last a very long time.

bad 83

iTrader: (3)

I pulled this engine from a cancer patient almost a year ago. I don't have a clue on how many miles were on it. I do know that the engine did not run for almot 4 years before I got it. I have beat on this engine for alomst 9 months. I'm not complaining.

yetterben

sam if yah wanna pick up those housings let me know. you can have them for cost man!

bad 83

iTrader: (3)

Thanks Ben. I'm going to try and con Stu out of one of those 12As he has. Two we know were running when pulled. One had a coolant leak, and the other was leaking oil. I would like to build a big street port, or a hlaf bridge, but I just want to get her back on the road for now. I was wanting to wait till this coming winter to build a bad *** N/A for the SA just to see how she would hold up to the Turbo FB. We'll see how this week goes, then I'll decide.

bliffle

Why did your apex seal let go? Do you often rev high? What kind of oil do you use? Do you premix or OMP? Do you have a trick ignition system?

etc.

I'm trying to understand what leads to apex seal failure in a NA engine. Especially since I've owned several rotaries and never lost an apex seal.

bad 83

iTrader: (3)

I have been driving this car pretty hard since I put her on the road. I think she was just worn out. I was hoping that the engine would have lasted till this winter, but O'well. I will be tearing this one down to see whats salvagable. I didn't have any warnings whatsoever that it was going to let go. It was just like flipping a switch when it went. No clue. Car was running just fine, then started missing.

gsl-se addict

iTrader: (3)

Same with my SA, bliffle. Everything was stock. Just going along not driving hard or anything. Power dropped big time all of a sudden and started running poorly. For a minute, I thought that I had just ran out of gas. I coasted into a gas station, refilled..still bad. Checked for sparked, disconnected wires/hoses, but everything else was okay. Typically the apex seals just wear well beyond their limit until they reach a point where they are simply too thin and either fall out, break, or crack. For some reason, the rear rotor likes to go 1st. Some blame the shutter valve, but my car didn't have one.

Even though I was running on half of an engine, I could still drive fine (no power at all, though). No smoke or anything..idle was rough..but you could drive it. It would top out at like 55 mph and would take a long time to even get up to that speed. But I would like to see a piston engine be drivable if it lost half of its pistons/rods..

Jeezus

iTrader: (4)

Yeah, got your message Let me know when you have any free time, can run up ther and help ya install it. Only thing I know is we gotta swap some engine parts around between the two.

Call you in a few

yetterben

**** you will be back on the road buy dinner time sam. Must be nice to have killer local support.

84stock

iTrader: (5)

The support you get is directly proportionate to the support you give. Help others out in need when you can and with what you've got, then it's money in the bank when you need it. The help just comes your way. Drive past a broken down motorist and laugh, you'll be stuck on the side of the road one day too.

yetterben

That totally negates the fact that i am the only real 7 owner in my area out side of some stupid ricer kids who just know turbo and sticker power. I have helped many a person out for free when i can!

It must be nice to have such a great group of guys to form such a tight community of people that will help each other out. Its hard when you're all alone and the only help you get is from people that are thousands of miles away.

Sam has always helped me when i need it and i will always help him in anyway i can!

ray green

iTrader: (14)

You can't beat the SE region for it's RX-7 generosity! Sam I hope you end up with the engine that came out of the Tan One, my 84 GSL (the one with the O ring oil leak). That was always a strong engine and it should be fine inside.

Jeezus

iTrader: (4)

He is on his way over now. The engine I have left did not have the front cover leak. Any idea what car that came out of? I am going to go back through my PMs.

Jeezus

iTrader: (4)

Here we go, old PM:

Hi Stu, glad there were no more misadventures, those engine look great in you trunk.

You can tell which one has the oil leak (the engine that came from the tan 84 GSL) because someone tried to use epoxy or PC weld to seal the leak from the outside, a repair that was done before I got the car and discovered only after I started cleaning up the engine. This "repair" seems to have worked pretty well actually, as I mentioned I drove the tan car for about 50,000 miles, controlling the oil leak very effectively by adding an oil sealer with each oil change and using 20-50W castrol. Although it has the oil leak, I've always felt that this engine is a good bet for a rebuild because I know it's entire history and it was never abused. This engine was running fine when I parked the car when it developed carb problems (flooding).

I'm less sure about the other engine, which came from the brown 85 GSL. When I bought the car it had about 110.000 miles on it. I added about another 60,000 miles or so, so it could have 170,000 miles on it. Or else it might have been a rebuild, with probably about half that many miles. I have no idea of how it was treated by previous owners, but the brown car was completely stock, even had the cats, and there was no evidence of hot rodding. In any event the brown engine always ran fine, never had an oil leak or problem with it, and it was my daily driver, when it got retired because of an encounter with a Buick about two years ago.

Both engines were stored with ATF or mystery oil soaking the chambers and protected from the weather.

Let me know how it goes. How's the hand?



---------------

Looks like the brown GSL one

Joker1337

Sucks about the seal, but this may be a record for blown engine to rebuilt time. 90 minutes to pull it solo? Nice.

vipernicus42

iTrader: (4)

Damn Sam, it always sucks to lose an apex. Good thing you've got another car, and that it's not your first engine swap.

Like you were saying, rebuild it stronger, faster, better

Jon

bliffle

I'm trying to understand why apex seals go out. Of course they could just wear away, but many reports just make that unlikely in most of the cases I've read about.

I believe that you can postpone seal wearout for a long time by using a good premix, as the ordinary sump oil may be inadequate (altho it may be OK for 100k, the usual design mileage).

I believe you can avoid a Forced Rupture of the seal by avoiding excessively high overrevving, since new modes of vibration are excited by high revs. Also, high revs and high oil viscosity may combine to cause cavitation and lube breakdown so I use 10w30 synthetic sump oil and am switching to 0w30.

I'm trying to decide which 2 of my 3 FBs to keep, and my original thought was to sell the 85GSL (80k) because it's such a sweetheart (even has the new car smell still) I though I could get a decent price, but no luck. Thought I'd keep the SE but it has 175k so maybe I should sell it. then I'd drive the 83GS and keep the 85GSL in reserve for the day that the 83 gives out.

I'm not at all convinced that apex seal failure is inevitable, except with a very large number of miles and wear. Most of these cars never get a chance to go extended miles before they are abused and neglected into failure.

yetterben

number one failure i believe is neglect. But since most of us are still using the original power plant we have no control of what happened before are cars landed in hand of rotor head's Once we get a hold of them and they are propally taken care of few problems arise. If you took a poll on people who have rebuilt or reman motors how long they last i bet its substantially higher than the stocker's.

Jeff20B

iTrader: (13)

I like to rebuild every engine I get so I know what's in it and can replace anything that's worn while I'm in there. I've never broken an apex seal so my aproach must be working.