13B Transplant Hoses - Revisited
#1
Go Hawks!
Thread Starter
iTrader: (1)
Join Date: May 2004
Location: Cedar Rapids, Iowa
Posts: 1,933
Likes: 0
Received 0 Likes
on
0 Posts
13B Transplant Hoses - Revisited
I posted a question a while back about what hoses to use for the S5 13B I'm putting into my '85 GS. I thought I'd post an update to show what hoses I used.
There are two fittings on the center iron...one directly out of the iron and the other on the oil filler tube. For the one coming directly out of the iron, I ran a hose to the tube that runs to the charcoal cannister. For the one on the oil filler tube I attached a breather that I got at AutoZone.
There is a fitting in the rear iron and one on the water pump housing that were for lines to the throttle body on the original 13B fuel injection system. I capped these with a short hose and a bolt.
For the heater hoses coming out of the firewall, the one on the passenger's side that goes to a tube that runs to the lower radiator hose is the stock '85 12A hose. The tube has another fitting just below this hose...I capped it with a short piece of hose and a bolt. The hose that connects to the other firewall fitting is from a '79 and runs from the firewall fitting to the rear iron just below the oil filter.
The hose that connects to the side of the lower radiator hose fitting is the stock '85 12A hose.
The upper radiator hose is the stock 12A hose.
For the lower radiator hose, I ordered the stock 12A hose, but it didn't fit right...there is not enough offset in it.
So I had my local AutoZone order the hose from an '85 GSL-SE in hopes that it would fit...it's perfect. On the left is the 12A hose, and on the right is the GSL-SE hose.
Here it is on the car.
There are two fittings on the center iron...one directly out of the iron and the other on the oil filler tube. For the one coming directly out of the iron, I ran a hose to the tube that runs to the charcoal cannister. For the one on the oil filler tube I attached a breather that I got at AutoZone.
There is a fitting in the rear iron and one on the water pump housing that were for lines to the throttle body on the original 13B fuel injection system. I capped these with a short hose and a bolt.
For the heater hoses coming out of the firewall, the one on the passenger's side that goes to a tube that runs to the lower radiator hose is the stock '85 12A hose. The tube has another fitting just below this hose...I capped it with a short piece of hose and a bolt. The hose that connects to the other firewall fitting is from a '79 and runs from the firewall fitting to the rear iron just below the oil filter.
The hose that connects to the side of the lower radiator hose fitting is the stock '85 12A hose.
The upper radiator hose is the stock 12A hose.
For the lower radiator hose, I ordered the stock 12A hose, but it didn't fit right...there is not enough offset in it.
So I had my local AutoZone order the hose from an '85 GSL-SE in hopes that it would fit...it's perfect. On the left is the 12A hose, and on the right is the GSL-SE hose.
Here it is on the car.
#2
Suicidal Death Missile
Join Date: Mar 2004
Location: Newport News, Virginia
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
Excellent info.
I don't know if I would suggest capping coolant lines with a bolt and a clamp though. I would try to route them to just form a circle. If you are bent on using the bolt, then at least put silicone on the hose and use a fuel injection hose clamp. You don't want that thing blowing off.
I don't know if I would suggest capping coolant lines with a bolt and a clamp though. I would try to route them to just form a circle. If you are bent on using the bolt, then at least put silicone on the hose and use a fuel injection hose clamp. You don't want that thing blowing off.
#5
backyard tuner
iTrader: (1)
Join Date: Sep 2002
Location: BC, Canada
Posts: 1,265
Likes: 0
Received 0 Likes
on
0 Posts
that breather filter is gonna get dirty so quickly. i just left mine open for now. hehe
also capping coolant lines hasnt caused a prob for me in almost a years use. just clamp er down good and its good to go (aslong as it isnt a high pressure area).
also capping coolant lines hasnt caused a prob for me in almost a years use. just clamp er down good and its good to go (aslong as it isnt a high pressure area).
#6
Old Fart Young at Heart
iTrader: (6)
I would put a breather on the lower nipple. The first time I filled my rebuild with oil, I had both nipples open, oil ran out of the upper one. I have since capped it and left the lower one open. There is a good chance that your breather will fill with oil on the inside, if you pour the oil in quickly.
Outstanding work btw.
Outstanding work btw.
#7
would it cause a problem to leave both of the holes open where you out the oil breather and the line that goes to the charcoal canister? Or what if I connected these two holes together with a hose? Let me know what you think thanks.
Thread
Thread Starter
Forum
Replies
Last Post
24seven_dada
3rd Generation Specific (1993-2002)
20
11-10-18 12:03 PM