My first choice for a gen 1 would be Work Equip, or fins.
But still love the old mesh style, or panasports.

 

Polished up, new valves, starting to look for some tires for them now. Will be getting new vinyl stickers made up for them too.

Anyone swapped out bolts before? Having a hard time finding ones that match these.

14" Hoshino Impul's, 6" on front, 7" on rear for the GSL-SE
15" x 7" Auto Bahns for the GS

 

Autobahns in gold....not my first choice but they do look nice. Diggin' the impuls....those would look nice on an early corolla...

 

Are you looking for the style of bolt head? or are you looking to switch from lug bolts to lug nuts?

 

Is it shameless to say my 13x7 4x110's are up for sale now?

https://www.rx7club.com/wheels-tires...24400-1031793/

on another note i'm finally getting around to blasting and painting these simmons i've got, any recommendation for tire sizes for 16x7's with slight lowering springs? The rest of the car is on tire dollies, so the entire thing is sitting up 2-3" high or so. Test fitting them had me a little scared due to the sa waffle wheel bolts i was using bottoming out before they were even close to securing the rim(forgot those were longer), but then i remembered i already had some spline drive bolts laying around to use :P

 

how are these? for hot/rare?

 

Yes those are.
They are the only stock wheels in the world I would drop money on.

 

i'v got 2 sets

 

Would you be willing to sell a set? Haha those are beautiful!

 

Im going to re finish the not so great looking ones the clear is flakinf off one set. And the good set is on the car. I also plan on using the not zo great ones with some drag radials eventually

 

I know those rotor wheels are rare, But I think they are uglier then the stock wheels...

 

Apparently my other pic links are broken so here's a couple newer shots.

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

 

Work Equips

Great wheels, but this particular size is impossible to find parts/lips for.

 

You can always go custom.
The guys over at Stanceworks do it all the time.

 

Sort of an FD look for a body kit'd FB.

 

Heres a revised shot with appropriate ride height of my S2 w/ 15x8 +10 offset Rota Shakotans (Hyashi street ripoffs) . Pic may be decieving, but I assure you I was lower than the roof line of partially dropped Miatas w/ the top down

 

Sarge, those are my favorites. What tire sizes?

 

205/50R15 Bridegestone RE-11's :bigthumbs:

 

I know these are rare. They have such a deep offset I know they'll only work on wide body or large flares
http://www.flickr.com/photos/83659599@N04/8864108312/

 

Nice stance! Im running the same size wheel (weds autobahns) and offset, but the fronts dont fit that nicely tucked in. Im running a 195/50/15 also. I dont know if the respeed kit makes the track on front a bit wider. Gotta look into that.

 

^ coil overs wont change the track width, are you running camber plates in the front?

As it sits currently, Im actually actually running ~5.5 mm wheel spacers in the front to clear the outer tie rods, which began to rub the inner lip of the wheel when I installed my 1" roll center adjusters, so in essence my fronts are sitting as tho they are actually +4 offsets. Also, I wouldnt have been able to get as low in the front w/o the spacers because the coilover adjuster lock rings would rub the tire (only other option would be to find some 6" coilover springs as opposed to the 7" ones im running) and lastly Im usually running ~ -2 degrees of camber in the front which also helps gain wheel well clearence

 

Not running coilovers, just stock gslse setup with tokico adjustables. Its the Respeed rack/pinion kit. What camber plates are you using? I've been looking around to go that route so it will give me better/more alignment options. Even though the kit gives me a bit of camber option, it's all in the bottom of tire. I'd like to be able to dial it all in using both top and bottom.

 

That FB looks like it's on it's way to being an FD.

 

What kind of dog is that? She looks awesome. But where are its ears?!?

 

i'll bite...rare as in i've never seen another fb with bassetts