Wolf 3D anyone with write up on wireing 3d.v4 with cas
#1
Rotary Enthusiast
Thread Starter
Join Date: Feb 2002
Location: ct
Posts: 828
Likes: 0
Received 0 Likes
on
0 Posts
anyone with write up on wireing 3d.v4 with cas
well i have a wolf 3dv4 and what do i need to hook it up with stock cas and coil packs has any one hooked it up with stock coils and cas any diagrams floating around
#4
Learned alot | Alot to go
iTrader: (2)
Join Date: Apr 2002
Location: Rotaryland, New Hampshire
Posts: 4,232
Likes: 0
Received 0 Likes
on
0 Posts
I run a stock cas
Stock coils work but the ignitor will not unless you have ordered your ems flashed to allow it to control the overenginnered trailing ignitor
Just buy a FD ignitor, which is a 3 channel unit, and you can control all 3 coils from it, or just the trailing if you wish
CAS writeup
https://www.rx7club.com/showthread.p...ght=CAS+Wiring
Ignitor write up
https://www.rx7club.com/wolf-3d-125/howto-fd-igniter-wolf-3d-v4-389233/
g'luck, post more questions if ya got em, however most wiring thiings have been covered so feel free to search
Stock coils work but the ignitor will not unless you have ordered your ems flashed to allow it to control the overenginnered trailing ignitor
Just buy a FD ignitor, which is a 3 channel unit, and you can control all 3 coils from it, or just the trailing if you wish
CAS writeup
https://www.rx7club.com/showthread.p...ght=CAS+Wiring
Ignitor write up
https://www.rx7club.com/wolf-3d-125/howto-fd-igniter-wolf-3d-v4-389233/
g'luck, post more questions if ya got em, however most wiring thiings have been covered so feel free to search
#6
Rotary Enthusiast
Thread Starter
Join Date: Feb 2002
Location: ct
Posts: 828
Likes: 0
Received 0 Likes
on
0 Posts
just buying the one fd ignitor is all i need? for ignition and i wire that to the plug near the battery for the leading coil ,,,by the way i have a msd will that do it and how i wire that up ..sorry for all the questions i read a few post but my electronic skills suck thanks guys for any info
Trending Topics
#11
Learned alot | Alot to go
iTrader: (2)
Join Date: Apr 2002
Location: Rotaryland, New Hampshire
Posts: 4,232
Likes: 0
Received 0 Likes
on
0 Posts
per nyt..
This is looking at it with the pins on the igniter facing up, looking at the top side of it. Pins from left to right. This matches up with the diagram on page G-16 of the FSM. Make sure you have the connector from the FD harness with the igniter also.
PIN 1 - Trailing Wolf (T1)
PIN 2 - To Trailing Coil (T1)
PIN 3 - Trailing Wolf (T2)
PIN 4 - 12V IN (switched)
PIN 5 - To Trailing Coil (T2)
PIN 6 - Leading Wolf
PIN 7 - To Leading Coil
PIN 8 - Unused (bridged to pin 7 inside the igniter)
from the FSM.
This is looking at it with the pins on the igniter facing up, looking at the top side of it. Pins from left to right. This matches up with the diagram on page G-16 of the FSM. Make sure you have the connector from the FD harness with the igniter also.
PIN 1 - Trailing Wolf (T1)
PIN 2 - To Trailing Coil (T1)
PIN 3 - Trailing Wolf (T2)
PIN 4 - 12V IN (switched)
PIN 5 - To Trailing Coil (T2)
PIN 6 - Leading Wolf
PIN 7 - To Leading Coil
PIN 8 - Unused (bridged to pin 7 inside the igniter)
from the FSM.
Thread
Thread Starter
Forum
Replies
Last Post
toplessFC3Sman
2nd Generation Specific (1986-1992)
6
03-20-18 01:54 PM