Post Pics of your FD Wheel Fitment!!
#1851
Junior Member
#1856
Full Member
iTrader: (3)
Hey guys i need some advice. i searched over 30 pages on here and was not able to spot what i was looking for.
but i have no idea what size wheels to get... not even worried about crazy fitment just to get close to flush.. my OZ's are 8" by +34 or 35 with a 25mm spacer. and they are inches away so i figure im going to need something in the - offset and maybe in the 10's to 11's?
but i have no idea what size wheels to get... not even worried about crazy fitment just to get close to flush.. my OZ's are 8" by +34 or 35 with a 25mm spacer. and they are inches away so i figure im going to need something in the - offset and maybe in the 10's to 11's?
i plan to run an 18x12 with a +20ish offset. or 18x11 to 11.5 with a -10 to 0 offset
tires would be 315 wide at least
#1858
Can Post Only in New Member Section
Looking to run some work equips on a stock body with just a mild roll, they would be
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
#1859
Rexxy
iTrader: (40)
Looking to run some work equips on a stock body with just a mild roll, they would be
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
#1860
Can Post Only in New Member Section
Do you know if the paint will hold up with a mild pull? Don't fancy doing any repainting. I would be using plenty of heat etc in the process
Also, it will be going pretty low, but again, nothing extreme as I want the car to be fully functional and able to get over speed bumps as there are loads of them where I live
#1861
Rexxy
iTrader: (40)
Thanks, that doesn't sound too bad, I could probably do a bit of a pull.
Do you know if the paint will hold up with a mild pull? Don't fancy doing any repainting. I would be using plenty of heat etc in the process
Also, it will be going pretty low, but again, nothing extreme as I want the car to be fully functional and able to get over speed bumps as there are loads of them where I live
Do you know if the paint will hold up with a mild pull? Don't fancy doing any repainting. I would be using plenty of heat etc in the process
Also, it will be going pretty low, but again, nothing extreme as I want the car to be fully functional and able to get over speed bumps as there are loads of them where I live
Dont use too much direct heat or you will heat up your paint and can bubble up lol
#1862
Lenny
iTrader: (9)
Jose is right, like always when it comes to this stuff. I'm running a slightly more aggressive setup than you want, FDliam. I have 18x10 +12 in the rear with 255/35 tire, 18x10 +25 front 245 tire. I had to run a small amount of rear camber, rolled fenders, and a very slight fender pull in the rear. My car sits pretty low but doesn't have any rubbing issues. Fender pull was done with a fair amount of heat and pulling VERY slowly, just not too much heat like Jose said.
Hope these pics help!
Hope these pics help!
#1863
Can Post Only in New Member Section
Thanks for the help guys, it seems like a manageable amount of pull so I might go for the equips
Also, yours looks amazing! love the combination, thanks for posting.
Also, yours looks amazing! love the combination, thanks for posting.
#1865
500+hp club
iTrader: (26)
Help
OK so i need some help guys.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
The following users liked this post:
esoterias17 (07-04-21)
#1866
Rexxy
iTrader: (40)
OK so i need some help guys.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
[/IMG][/URL]
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
[/IMG][/URL]
Blind shot i wanna say you are in the +19 to +25 area but most likely +19 They look a lot like some old wheels i had with those offsets.
#1869
Rotary Enthusiast
iTrader: (4)
Looking to run some work equips on a stock body with just a mild roll, they would be
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
Front: 18x9 +22
Rear: 18x10 +16
I would run some stretch but nothing extreme. Think I would get away with those sizes with something like a 245 or 235/35 on the 10 and maybe a 215 or 225/35 on the front?
Hope someone can help.
#1870
Failcopter..it's here..
iTrader: (6)
Join Date: Aug 2008
Location: near phoenix....kinda...
Posts: 721
Likes: 0
Received 1 Like
on
1 Post
OK so i need some help guys.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
#1871
Full Member
iTrader: (4)
Join Date: Feb 2011
Location: chicago
Posts: 89
Likes: 0
Received 0 Likes
on
0 Posts
OK so i need some help guys.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
I finally found the info on my jline wheels. They are stamps instead of castings and most of the stamp has been worn off. All 4 wheels are 17x9.5 with 225-45-17 tires all the way around and i have no idea what my offset is which SUCKS!
I plan on running 235-40-17 tires on the fronts and i want wider in the rears but since they are 9.5 and i like the small stretch i have now and want to keep it that way. I plan on pulling all my fenders just slightly and lowering the car also.
So i plan on ordering some new rear wheels from jline. I plan on getting 17-10.5's but i have no clue on offset. I want the same offset i have now so they match.
Here is the 9.5's all the way around. ANYONE WHO CAN GIVE ME A IDEA OF MY REAR OFFSET PLEASE HELP
As you can see i need wider tires in the back. Id love to fit 11" wide wheels if i could without pulling too far.
why don't you just measure the offset?
#1873
500+hp club
iTrader: (26)
im going to have to say that seems like a pretty low offset 9.5 . it sticks out more than my 18x10.5 +15 did. if u want to move up to 11's and stay stock body. with a meaty tires. then 18x11 +43 is about what u want(no real crazy stretch) would be a 295/30. (which u could actually do all around, be decently low, be stock body) if u wanted to push it a lil more u can do 10.5 +22 put a 265/35 and be fine . 17's im a bit rusty on for tires sizes.
#1875
500+hp club
iTrader: (26)
Silverfdturbo6port, The rear wheels look to be a very low offset to me, maybe +10 or lower. Here's a vid on how to measure offset
How to measure wheel offset - YouTube
How to measure wheel offset - YouTube
10.5=266.7
5.5=155.58
266.7/2=133.35
133.35-155.58=+22haha yea no these are not no +22 offset